13110 19TH AVE SE 2017-09-25 - Laserfiche WebLink

2012 Washington St Aergy Code Compliance Forms for Commercial,Group Rio>3 story R2 and R3 Mechanical Permit ' Page I of 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stones and all R1 Revised Aug 2015 Project Address 2205 BROADWAY Date 5/13/2016 The following information is necessary to check a permit application for compliance with the mechanicial systems and equipment requirements of the Washington State Energy Code,Commercial Provisions. Applicable Location in Building Department Code Section Code Provision Information Required-Must be in permit documents (yes,no,na) Documents Notes GENERAL PROVISIONS Equipment Sizing&Performance MECH- yes C403.2.1 Load calculations Load calculations performed per ASHRAE Std 183 or equivalent per Chapter 3 LOAD- CALC yes C403.2.2 Equipment and system Output capacities of heating and cooling equipment and systems do not exceed the next larger MECH-EQ sizing available equipment size above the calculated loads;note exceptions taken na C403.2.5 Minimum ventilation Ventilation(natural or mechanical)provided per IMC;indicate mechanical ventilation is capable of being reduced to minimum requirement per IMC C403.2.3& with type,SUM t complete MECH l equipment schedules Equipment minimum Provide a ui ues or corn -SUM we,ca acit ,efficiency, MECH yes C403.2.3.2& - e ncq p p yP P YSUM C403.2.12.1 efficiency test standard(or other efficiency source)for all mechanical equipment M-111& MECH- yes C403.2.13 Electric motor efficiency Provide equipment schedule with hp,rpm,and efficiency for all motors,note exceptions taken FANSYS- SUM na C403.2.10.1 Fan power limitation For all applicable systems>5hp,provide system total nameplate hp in MECH-FANSYS-SUM form na C403.2.10.1 Fan power limitation For all applicable fan systems>5hp,verify fan system motor hp or bhp complies with fan power limits per Table C403.2.10.1(1),provide MECH-FANSYS form for each system MECH- yes C403.2.10.2 Motor nameplate hp Indicate fan motors specified are the smallest available motor hp size greater than fan bhp, FANSYS- note exceptions taken SUM C403.2.10.3 MECH- yes &C403.2.13 Fractional hp fan motors Indicate fan motors 1/12 to 1 hp are ECM type or meet minimum efficiency req. FANSYS- SUM na C403.2.3 ca ximum air cooled chiller Indicate air-cooled chiller capacity does not exceed air-cooled chiller limit paty na C403.2.3.1 Non-standard water-cooled Full-load and NPLV values for water-cooled centrifugal chiller adjusted for non-standard chillers operational conditions na C403.2.12.1.1 Centrifugal fan cooling Large capacity cooling towers with centrifugal fan(s)meet efficiency requirements for axial fan towers open circuit cooling towers na C403.2.3 Forced air furnace and unit Indicate intermittent ignition or IID,flue/draft damper&jacket loss heaters na C403.2.3.3 Packaged electric Verify all packaged electric equipment that provides>20,000 Bluth cooling capacity and heating/cooling equipment heating is a heat pump,note in equipment schedule na C403.2.3.4 Humidification Indicate method of humidification(note requirements for systems with economizer) HVAC System Controls&Criteria yes C403.2.4.1 Thermostatic controls Indicate locations of thermostatic control zones on plans,including perimeter systems M-1 11 na C403.2.4.1.1 Heat pump supplementary Indicate staged heating(compression/supplemental)and outdoor lock-out temperature is set heat to 40°F or less M-111 yes C403.2.4.2 Setpoint overlap(deadband) Indicate 5°F deadband minimum for systems controlling both heating&cooling yes C403.2.4.3 Automatic setback and Indicate zone t-stat controls with required automatic setback&manual override M-111 shutdown yes C403.2.4.3.3 Automatic(optimum)start Indicate system controls that adjust equip start time to match load conditions M-111 C402.4.5.2& OSA,exhaust,and relief air Indicate location of outdoor air supply intake,and exhaust and relief outlet dampers;verify M-1 11 yes C403.2.4.4 dampers Class 1 leakage rating and control type motorized or gravity);note exceptions taken P 9 9 YP ( 9 Y). na C402.4.5.2 Return air dampers Indicate location of return air dampers that are integral to economizer operation;verify motorized control and Class 1 leakage rating;note exception taken na C402.4.5.1 Stairway and shaft vents Indicate location of stairway and shaft vents,verify Class 1 leakage rated motorized dampers and method of activation na C403.2.11 Heating outside a building Indicate radiant heat system and occupancy controls na C403.2.4.5 Snow melt systems Indicate shut-off controls based on outdoor conditions na C403.2.4.6 Combustion heating Indicate modulating or staged control equipment