Laserfiche WebLink
General Specifications <br /> System Power Supplies(SPS) 120 VAC Models 4 A maximum @ 102 to 132 VAC,60 Hz <br /> Input Expansion Power Supplies(XPS) 220-240 VAC 2 A maximum @ 204 to 264 VAC,50/60 Hz; <br /> Power Remote Power Supplies(RPS) Models separate taps for 220/230/240 VAC <br /> Power Supply Output Total Power Supply Including module currents and auxiliary power outputs; Output switches <br /> Ratings for SPS,XPS, Output Rating 9 A total for"Special Application"appliances;4 A total for to battery backup <br /> and RPS "Regulated 24 DC"power(see below for details) during mains AC <br /> (nominal 28 VDC on Auxiliary Power Tap 2 A maximum failure or <br /> AC;24 VDC on batteryNACs Programmed 2 A maximum per NAC; Rated 19.1 to 31.1 VDC brownout <br /> backup) for Auxiliary Power 5 A maximum total conditions <br /> Special Application Simplex horns,strobes,and combination horn/strobes and speaker/strobes(contact your Simplex product <br /> Appliances representative for compatible appliances) <br /> Regulated 24 DC Power for other UL listed appliances; use associated external synchronization modules where required <br /> Appliances <br /> Battery Charger Battery capacity range UL listed for battery charging of 6.2 Ah up to 110 Ah(batteries larger than 50 Ah <br /> Ratings for SPS and require a remote battery cabinet);ULC listed for charging up to 50 Ah batteries <br /> RPS(sealed lead-acid Charger characteristics Temperature compensated,dual rate, recharges depleted batteries within 48 <br /> batteries) and performance hours per UL Standard 864;to 70%capacity in 12 hours per ULC Standard S527 <br /> Environmental <br /> Operating Temperature 32°to 120°F(0°to 49°C) <br /> Operating Humidity Up to 93%RH, non-condensing @ 90°F(32°C)maximum <br /> Additional Technical Installation Instructions 574-848 <br /> Reference Operating Instructions 579-197 <br /> Mounting and CPU Bay M.dule Reference (* indicates supplied modules) <br /> Slot 3,one 2"card:either 4100-6078 Network Module <br /> with media cards or 4100-6038 Dual RS-232 <br /> s <br /> 1 <br /> Master Controller Bay 4100-6030 Service Modem mounts I <br /> only on master controller board O <br /> Two,2",or one,4"slot for .; C� Knockout Cabinet height: <br /> one or two modules installed - g <br /> """"' 4100-6031 or 4100-6032 screw/nail2 bayshown <br /> per the following: 7 Ci Circuit or 4100-6033 ( <br /> ty holes(for for reference) <br /> 4100-6052 DACT,Slot 1 II r [ Alarm Relay semi-flush <br /> 4100-6101 Physical Bridge, S1ot2 J mounting) 1 amm)2 <br /> Slot 2 slot 3) � (559 <br /> °o aim 2 Bay=40" <br /> 4100-6102 Physical Bridge <br /> 4'module)Slots 1 and2 (1016 m56 <br /> m) <br /> ( Master controller (*Systempower supply) For semi-flush .� f <br /> y pp y� mounting provide 3 Bay=56" <br /> 4100-6048 VESDA Interface, with motherboard , „, 1/2"(12.7 mm) (1422 mm) <br /> Slot 1 ort .. �W111• 1‘,... <br /> minimum extension P Wall board <br /> 4100-5005/5015 IDC Modules, ® beyond finished wall l� reference for <br /> Slot 1 ort .a° <br /> semi-flush <br /> 4100-6038 Dual RS-232, Ill ' mounting, <br /> Slot 2,if Network Module isj I: r t6"stud <br /> in Slot 3Typical Expansion Bay m W ® Stud <br /> (showing mixed module sizes) alignment <br /> markers, <br /> Two bay cabinet/'" each side <br /> shown without retainer Door 4-3/4" 6"stud <br /> (121 mm) il <br /> Battery Compartment I 4"stud <br /> • <br /> Door can be hung ( I ° <br /> hinged left or right I 24"(610 mm) 01I m2" <br /> (175 mm) <br /> Optional semi-flush trim kit 11-11/16" <br /> (296 mm) <br /> NOTE: A system ground must be provided for Earth Detection and transient protection devices.This connection <br /> shall be made to an approved,dedicated Earth connection per NFPA 70,Article 250, and NFPA 780. <br /> S4100-0031-30 12/2014 3 5, <br />