Laserfiche WebLink
SIEMENS Data Sheet <br /> Fire Safety Products <br /> FACP Accessories <br /> PAD-4 Distributed Power Supply Unit [for ®UL markets] <br /> Notification Appliance Circuit Extender <br /> Models PAD-4-ENCL, PAD-4-MB (with FP2011-U1, FP2012-U1 power supplies) <br /> ARCHITECT AND ENGINEER SPECIFICATIONS <br /> SIEMENS <br /> • Four(4)'Class B',power-limited notification appliance circuits(NACs) `j <br /> • 'Class A',field-selectable wiring s 1+ :•+; <br /> • Each unit can support an optional module(Model PAD-4-CLSA)that j <br /> converts two(2)built-in'Class A'NACs into four(4)'Class A'NACs 'Class A' <br /> • Up to 3 Amps of auxiliary-power output Adapter Card <br /> [Model PAD-4-CLSA] <br /> • Optional built-in strobe synchronization <br /> • Supports coded audible signals,including Temporal 3,Temporal 4 patterns <br /> A"it 'i�. }'L <br /> • Battery supervision and control IIIR[ ' <br /> • 'Form C general Trouble IAC Fail monitoring contact ..j,.r rl FA°4 <br /> • Power supplies support NAC power Main Board Unit Enclosure <br /> • Up to 6A used with Model FP2011-U1 [Model PAD-4-MB] [Model PAD-4-ENCL] <br /> • Up to 9A used with Model FP2012-U1 <br /> • 24VDC output voltage • Multi-module mounting in System 3TM'enclosures <br /> • Ground-fault detection • Multiple modules share battery set <br /> • Advanced microprocessor control • ADA Compliant <br /> • Uses Flash memory-based system firmware • ®UL 864 9th Edition Listed,®UL 1481 Listed; <br /> • Optional system-diagnostic and firmware-upgrade tool FM(#3010),CSFM (#7315-0067:0268)Approved <br /> Product Overview <br /> Used with Siemens—Fire Safety fire alarm control The PAD-4 unit provides consistent 24VDC output <br /> panels (FACPs),the Distributed Power Supply PAD-4 voltage to each NAC— independent of voltage <br /> Unit is a NAC expander with a built-in, auxiliary- fluctuations on the primary or secondary power <br /> power output. Each PAD-4 unit distributes source. As a result, a larger voltage drop and a <br /> additional power in buildings for audible and visual greater wire length for each NAC are supported by <br /> indicators that conform to the Americans with each PAD-4. <br /> Disabilities Act(ADA). PAD-4 also has the <br /> following features: Specifications <br /> • NACs This version of the Siemens Distributed Power Supply <br /> • Signal-input circuits Unit can be configured in the following manner that <br /> • Battery-charging circuit makes the outputs easily programmable: <br /> • Trouble relays for remote monitoring <br /> • <br /> • Diagnostic light-emitting diodes(LEDs) 'STEADY'outputs <br /> • <br /> • Alternating Current(AC)power connection Synchronized strobe outputs <br /> • American National Standards Institute(ANSI)Temporal 3 <br /> The Siemens NACs, which connect with alarm - ANSI Temporal 4[for carbon monoxide(CO)alarm signal] <br /> signaling devices, have been designed to provide There are also two (2) inputs used to control the <br /> the highest level of reliability and performance. <br /> Signal coding on the circuits is accomplished activation of the four(4) outputs. Programming can <br /> through integrated circuits (rather than relays), be set so one (1) input will silence the audible signal <br /> which eliminates mechanical wear on the output on Siemens Models'AS'-series, 'NS'-series, or'ZH'- <br /> circuits. series horn and horn-strobes while the strobes <br /> remain active. <br /> Distributed Power Supply— NAC Extender (Model PAD-4 series) 3363 <br /> SIEMENSIndustry, Inc. /y <br /> Building Technologies Division <br />