6920 SEAWAY BLVD 2019-07-08 - Laserfiche WebLink

Specifications — (continued) Operation of each PAD-4 unit is controlled by Each unit is packaged in its own sheet-metal firmware stored in Flash memory on the main board, enclosure with sufficient space to house up to 7AH as well as the storage of a 10-event log,which can battery sets.The enclosure (Model PAD-4-ENCL) is be viewed via Model PAD-4-FDT. In the event that available in red. an upgrade to the system firmware is required, the The battery charger used in each unit can energize firmware can be transferred to the system without batteries of up to 18AH. Though, when battery sets the replacement of firmware chips. greater than 7AH are required, the battery set must An optional firmware-download software tool, be housed in a System 3 enclosure or a separate Model PAD-4-FDT, can be used for system diagnostic ®UL Listed battery enclosure. testing of the following: System 3 enclosures may also be used to house • Primary-power voltage readouts multiple Model PAD-4 units in a single enclosure,via • Current draw for power charger • Configuration switch settings the Model S3AP Adapter Plate.Two(2) units are • Firmware version capable of sharing the same battery set when • Battery voltage mounted in the same enclosure. Model S3AP can When the tool is in communication with Model PAD'- also be used to mount the PAD-4 main board and 4-MB, the'Test Mode'LED is illuminated. Model 170-Watt power supply(Model FP2011-U1) into a PAD-4-LUA is a USB serial port adapter that is PAD-3 enclosure. required for tool-kit operation. Each Model PAD-4 unit complies with seismic Each NAC extender supervises a variety of functions certification, pursuant to the following: including: • ASCE Standard 7,2005 Edition • Low AC power • International Building Code,2006 Edition • Battery-voltage level • California Building Code,2007 Edition • Earth ground fault conditions • ICC-ES AC 156,effective 2007 All power can be directed to two (2)'Class A'or four • OSHPD preapproved,under: OSP-0057-10 (4)'Class B'power-limited NACs. Each NAC supports - OSHPD CAN 2-1708A.5,Rev.3 up to 3 Amps per circuit. Either one (1) or two (2) Each Model PAD-4-series unit also complies with inputs can control four(4) outputs,which are seismic certification, pursuant to ASC I SE! 7-05, compatible with all Siemens—Fire Safety 24VDC Section 13.2.2,when used with the PAD-4 battery alarm signaling devices. bracket(Model PAD4-BATT-BRKT). In cases where'Class A'circuits are used,an optional Model PAD-4-CLSA module can be added, providing Configuration Options two(2)additional'Class A'outputs to each PAD-4 unit. Option Inputs] Output Controls Circuit Types Each NAC extender is also capable of operating other 1 Input All outputs Class B'circuits parts of a Siemens fire alarm system, such as door 2 Input 1 All outputs Class B'circuits holders,via 3 Amps @ 24VDC max of power-limited Input z* Silences horns on Output 1 — auxiliary output. When the output activated,the 3 Input 1 Outputs 1 and 2 Class B'circuits total power available cannot exceed 6 Amps when Input 2 Outputs 3 and 4 Class B'circuits used with Models FP2011-U1 or 9 Amps when used 4 Input 1 Output 1 'Class B'circuits with FP2012-U1. Input 2 Outputs 2,3 and 4 'Class B'circuits Trouble conditions are monitored through each 5 Input 1 Outputs 1 through 4 'Class A' g circuit pairs unit's two (2) inputs. In addition, one(1)'Form C' 'Class A' Trouble contact is provided for monitoring each unit 6 Input 1 Outputs 1 through 4 circuit pairs that is connected through the input of a Siemens Input 2* Silences horns on Output 1 — FACP. Therefore,the user has the option of Input 1 Outputs 1 and 2 'Class A' connecting a PAD-4 NAC extender unit into a NAC of 7 circuit pairs a Siemens FACP, or the unit maybe monitored with Input 2 Outputs 3 and 4 'Class A' circuit pairs a Model TRI series monitoring module on a Siemens *denotes when used with Siemens Model A5,'NS'or'ZH'–series intelligent fire system. horn(strobe devices A separate'Form C'Trouble contact is used exclusively with each NAC extender to indicate AC Fail Trouble events on the NAC extender. SIEMENS Industry,Inc. Building Technologies Division q I