3003 W CASINO RD BLDG 40-23 2018-09-21

SPECIFICATIONS RADIOACTIVE MATERIAL Input Voltage: 16.5-27.5 Vdc Do not attempt disassembly of the fac- Standby Current: 350�A, typical � tory sealed sensing chamber. This assembly is sealed for your protection Alarm Current: 425NA, typical WARNING and is not intended to be opened for Max. Detectors per SLC: 255 servicing. Note: Ail detectors can be in alarm simultaneously. Less than 1.0 microcuries Americium 241 in ionization detector. Shielded by stainless steel housing. LED PULSE MODES APPLICATION DATA Normal: 9 second interval The smart detectors are compatible with control equip- Trouble: LED is off ment which utilizes the RX/TX Module. Each RX/TX can Alarm: 2 second interval communicate to 255 smart or addressable devices. The Operating Temperature: 32°F (0°C)- 100°F (38°C) circuitry may be either Class "A" or Class "B". Class "A" requires a series loop circuitry with the loop returning to EMI Immunity: Meets UL 268 the RX/TX. Class"B"does not require a return to the RX/ TX and permits T-tapping. SENSITIVITY All SmartOne detectors utilize the same base and may Open Area High Velocity be interchanged. Installation is both simple and fast using lonization 0.5- 1.5%/ft. 0.5- 1.0%/ft. screw-type connections and the non-polarized detector feature. The detector is fitted to the base by a twist-to- Photoelectric 0.5-3.5%/ft. 0.5-2.0%/ft. lock action.A removable locking tab secures the detector to the base to provide some degree of vandal resistance THERMAL DETECTOR SPACING or inadvertent removal. 50 ft.: 135°F(57°C)- 145°F(63°C) Note: While units are interchangeable, changing detec- 70 ft.: 135°F(57°C)- 155°F (68°C) tor type will require a change in system program- Thermal detectors are limited to 20 ft. spacing when used ming. on FM approved applications. SMARTONE IONIZATION SMOKE DETECTOR Note: These detectors are compatible only with fire CPD 7052 models are dual chamber ionization type alarm systems utilizing an RX/TX Module. detectors which sense both visible and invisible smoke.A unique sensing chamber design permits full 360 degree INSTALLATION smoke entry and response. Detector bases are mounted directly to a 4-in. octagonal SMARTONE PHOTOELECTRIC SMOKE box. Please refer to NFPA 72-2002 for spacing, location DETECTOR of detectors and other guidelines.Also, refer to our Publi- PSD 7152 models are smart photoelectric smoke detec- cation 74-212 for detailed installation instructions. tors. These detectors will respond to a broad range of The detector base is equipped with an integrally molded flaming and smoldering fire conditions. locking tab to prevent unauthorized removal. Once SMARTONE THERMISTOR HEAT DETECTOR locked into place, the detector can be removed only by Model THD 7252 are thermistor based analog devices inserting a screwdriver blade into the slot while turning that can be programmed to respond to fixed temperature the detector head counterclockwise. If the detector is to without problems associated with thermal lag. be mounted on a ceiling high enough to cause difficulty in SMARTONE DETECTOR MOUNTING BASES accessing the unit, it is recommended that the locking tab be removed prior to installation. To remove locking tab, All models of SmartOne detection devices use a univer- bend outward until it breaks off. sal mounting base arrangement. The mounting base is available in two models, Model 6SB and Model 4S6. MAINTENANCE Base model 6SB provides a trim ring which masks any The minimum requirement for detector maintenance con- inconsistencies between the electrical box and the ceiling sists of an annual cleaning of dust from the detector head material. Model 4SB is electrically the same as model using vacuum cleaner suction. Cleaning programs 6S6 but does not provide the trim ring. The 4SB outside should be geared to the individual environment. diameter matches that. of the detection devices thus allowing installation into tight spaces (i.e., underfloor areas). -3-