3003 W CASINO RD BLDG 45-12 2018-09-20

Building Permit Plans ecklist, pg. 1 ENV-CHK 2012 Washington State Energy Code Compliance orms for Commercial Buildings including R2&R3 over 3 stories and all R1 Project Address Boeing Everett Facility Date 9/4/2015 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy Code,Commercial Provisions. Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes SCOPE na C101.5.2 Low energy spaces Low energy spaces identified on plans na C101.5.2.1 Semi-heated spaces Semi-heated spaces identified on plans C402.1.4 C402.5 Cooler and freezer Walk-in and refrigerated warehouse cooler and freezer spaces identified on na C402.6 spaces plans na C101.4.6 Mixed occupancy Spaces with different occupancy requirements identified on plans C101.4.4 Change of Existing F,S and U-occupancy building spaces undergoing a change of na C101.4.5 occupancy/space occupancy or space conditioning that require compliance are identified on conditioning plans ENVELOPE PROVISIONS yes C303.1 Insulation Indicate identification mark shall be applied to all insulation materials identification A200 C303.1.3 Fenestration product Fenestration products shall be labeled with rated U-factor,SHGC,VT,and na C402.4.3 rating leakage rating Indicate installation methods,thicknesses,densities and clearances to C303.1.1 General insulation achieve the intended R-value of all insulation materials; yes C402.2 installation Where two or more layers of rigid insulation will be used,indicate that edge RFA160-10 thru joints between layers are staggered RFA160-15 Indicate R-value(s)of cavity/continuous insulation on roof sections; Indicate framing materials on roof sections; Indicate method of framing for ceilings below vented attics and vaulted yes C402.2.1 Roof assembly ceilings per A102.2(std,adv); insulation Provide area-weighted calculations for sloped insulation installed entirely above deck; Indicate R-values for thermal spacers and each insulation layer,and liner RFA160-10 thru system(LS)method for metal building roofs RFA160-15 na C402.2.1 Skylight curb Indicate curb insulation R-value on roof section if not included in skylight insulation NFRC rating Indicate R-value(s)of cavity/continuous insulation on wall sections; Indicate framing materials on wall sections; C402.2.3 Indicate method of framing for wood const per A103.2(std,int,adv); yes C402.2.4 Above/below grade Indicate mass of masonry walls; wallin C303.2.1 `Nall insulation Indicate loose-fill core insulation material,percentage of cores filled,and frequency of grouted cores and bond beams for masonry walls; Indicate method of protection of exposed exterior basement/crawlspace wall insulation A200 and A500 Walk-in/refrigerated Indicate insulation R-values of ceilings,walls,doors,floors on sections; na C402.5 warehouse cooler Indicate method of minimizing door infiltration; C402.6 and freezer insulation Indicate type(s)of transparent doors and windows yes C402.2.7 Opaque doors Indicate rated U-factor(swinging)or R-value(roll-up/sliding)on wall sections- applies to doors with less than 50%glazed area A500 Floor over outdoor or Indicate R-value(s)of cavity/continuous insulation on floor sections; na C402.2.5 unconditioned space Indicate framing material on floor sections; insulation Indicate mass of masonry floors Indicate R-value of continuous insulation on wall section or foundation detail; C402.2.6 Slab-on-grade floor Indicate insulation extends down vertically and/or horizontally the required yes C303.2.1 insulation distance from top of slab; Indicate method of protection of exposed exterior slab edge insulation A200 and A500 Indicate R-value of continuous insulation on wall section or foundation detail; C402.2.6 Radiantly heated Indicate insulation extends down vertically from top of slab and then na slab-on-grade floor C303.2.1 insulation horizontally under the entire slab; Indicate method of protection of exposed exterior slab edge insulation Radiant heating Indicate insulation R-value behind radiant panels,U-bend/headers and na C402.2.8 bottom surface of radiantly heated floors(other than radiantly heated slab-on- system insulation grade) (1&