3003 W CASINO RD BLDG 45-12 2018-09-20

Description Should the operator or installer forget to program the detector,.the HFP-11 will revert to a default setting that The HFP-11 is a plug-in,two-wire,multi-sensordetector allows it to operate as an office environment detector. with both photoelectric and thermal inputs and is compat- ible with Fire Finder XLS and FS-250 series of control The HFP-11's FirePrint technology monitors input from panel systems. Each detector consists of a dust resis- both the photo chamber and the thermal sensor, tant,field-cleanable photoelectric chamber,a solid state evaluating this information with sophisticated math- non-mechanical thermal sensor,and microprocessor ematical formulas, or algorithms, comparing this input based electronics with a low-profile plastic housing.The to characteristics of both threatening fires and decep- HFP-11 utilizes state-of-the-artASIC circuitry and surface tive phenomena that would "fool" any ordinary detec- mounttechnologyformaximum reliability. Every HFP-11 tor.This technology was developed over years of fire detector is shipped with a protective dust cover.The research and reviewing the results of over 20 years of HFP-11 fire detector utilizes an infrared light emitting fire test data in one of the worid's most advanced fire diode(IFiLED),and light sensing photodiode. Under research centers. normal conditions, light transmitted by the LED is directed away from the photodiode and scattered through The results of this research are the mathematical the smoke chamber in a controlled pattern.The smoke models that form the algorithms used in FirePrint. No chamber is designed to manage light dissipation and other fire detector has this level of intelligence or this extraneous reflections from dust particles or other non- amount of research and development supporting it's smoke airborne contaminants in such a way as to main- design.The microprocessor's software can identify tain stable,consistent detector operation.When smoke and disregard false input caused by radio frequency enters the detectorchamber,light emitted from the (RFI) and electromagnetic (EMI) interference, and IRLED is scattered by the smoke particles and is received validates all trouble conditions before annunciating or by the photodiode. reporting to the control panel.The HFP-11 detector's microprocessor uses an integral EEPROM to store the The HFP-11 also utilizes a modern,accurate,shock- detector's address and other critical operating param- resistant thermistor to sense temperature changes. eters which include the assigned program values for The "on-board" FirePrint technology allows the detec- alarm and trouble thresholds. tor to gather smoke and thermal data, and to analyze this information in the detector's "neural network"By Communications within the detector itself and be- comparing data received with the common characteris- tween the HFP-11 and the control panel, or with the tics of fires, or fire fingerprints, the HFP-11 can com- DPU field device programmer/tester unit, are super- pare these "Fire Prints" to those of deceptive phe- vised and safe-guarded against disruption by reliable, nomena that cause other detectors to false alarm.The, microprocessor based error checking routines. Addi- advanced FirePrint technology allows the HFP-11 to tionally, the micro-processor supervises all EEPROM accurately determine a true fire hazard from a non- memory locations and provides a high degree of threatening deceptive phenomena WITHOUT needing EEPROM failure fault tolerance. to use alarm delaying verification and confirmation The HFP-11 determines its operating status to be techniques, which can increase the probability of normal; in alarm, or in trouble depending on the losses due to fire.The HFP-11 provides the highest difference between the alarm threshold values stored level of detector intelligence available today with a in the detector's memory and the detector's latest detector/control panel link that allows the user to analog measurement.The detector then communicates program the detector for the specific hazard profile changes in its status to the control panel. In addition, using a simple software menu selection. Detectors the FireFinder XLS control panel will sample the value are optimized by selecting one of the following eleven of the HFP-11's analog signal over a period of time in applications: order to determine if those values indicate excessive • Office/Retail buildup in the photo chamber;if so,the FireFinder XLS • Lobby control panel will indicate that the particular detector • Computer Room requires maintenance. • Dormitory The HFP-11 is listed as a self-testing device.The • Healthcare HFP-11's visible light emitting diode (LED) flashes green every 4 seconds to indicate it is communicating • Parking Garage with the control panel and that it has passed its • Utility/Transformer Room internal self-test. Should the detector sense a fault or • Hostile Environment failure within its systems, the LED will flash amber • Precious Storage and the detector will transmit that information to the • Air Duct control panel. A quick visual inspection is sufficient to indicate the condition of the detector at any time. If •Warehouse/Light Manufacturing more detailed information is required, a printed report The software does the rest; no guessing on detector can be provided from the Fire Finder XLS panel sensitivities or alarm verification; the control panel indicating the status and settings assigned to each programs the HFP-11 detector for the protected area individual detector.When the HFP-11 moves to the without hassle and without confirmation delays. Once alarm mode, it will flash red and to continue flashing optimized for the hazards in the protected area, the untii the system is reset at the control panel. At that HFP-11 provides the best detection you can buy.