|
same time,any user defined system alarm functions ceilings may also affect safe spacing limitations for
<br /> programmed into the system are activated. detectors. Should questions arise regarding detector
<br /> Detectorsensitivity,calibration,and identification placement, observe NFPA 72 guidelines. Good fire
<br /> are dynamically supervised by the control panel. protection system engineering and common sense
<br /> Detector sensitivity and pre-alarm levels are a function dictate how and when fire detectors are installed and
<br /> of the application chosen at the control panel and are used.Contact your local Fire Safety distributor or sales
<br /> controlled by the panel. If an alternate, non-FirePrint office wheneveryou need assistance applying FirePrint in
<br /> mode is selected, then the sensitivity can be changed unusuai applications.Be sure to follow NFPA guidelines
<br /> from the control panel. and UL/ULC approved installation instructions,which are
<br /> included with every Fire Safety detector,and local codes
<br /> The DPU Device Program/Test Unit accessory is used as for all fire protection equipment.
<br /> to program and verify the detector's address.The
<br /> technician selects the accessory's program mode
<br /> to enter the desired address.The DPU automatically Dimensions
<br /> sets and verifies the address and tests the detector.
<br /> The DPU operates on AC power or rechargeable 6°DiameterBase —
<br /> batteries, providing flexibility and convenience in
<br /> programming and testing equipment almost anywhere.
<br /> When in the test mode, the DPU will perform a series T
<br /> of diagnostic tests without altering the address or I
<br /> other stored data, allowing technicians to determine
<br /> if the detector is operating properly.The HFP-11 fire o�au
<br /> detector may be installed on the same initiating He�ght
<br /> circuit with HMS series manual stations, HTRI series �
<br /> interfaces, HCP output control devices, or HZM series
<br /> of addressable, conventional zone modules. All HFP-11
<br /> detectors can be cleaned in the field, when required,
<br /> by simply removing the detector cover and unsnapping
<br /> the photo chamber.There is also the option of cleaning Technical Specifications
<br /> the interior of the detector with a clean, soft cloth Operating Temperature: +32°F (0°C) to 100°F (38°C)
<br /> or brush, or replacing the labyrinth and bug screen per UL 268/268A
<br /> included in the detector maintenance kit, model
<br /> DMK-11. Humidity: 0-93% Relative Humidity
<br /> Non-Condensing
<br /> The HFP-11 uses the low-profile surface mounting
<br /> base, model DB-11.This base mounts on a 4-inch Maximum spacing: 30 foot centers (900 sq. ft.)
<br /> octagon, square, or a single gang electrical box. per NFPA 72 Chapter 5 and
<br /> The base utilizes screw clamp contacts for electrical CAN/ULC-S524
<br /> connections and self-wiping contacts for increased
<br /> reliability.The base can be used with the optional
<br /> LK-11 detector locking kit which contains 50 detector - - -- - - P��--
<br /> locks and an installation tool, to prevent unauthorized ��a�d� D�a��ri���o� ������
<br /> removal of the detector head.The DB-11 base has '--�-�. ����� ,����,�����,���;,��,f�p,�,��,�� ��.a�
<br /> integral decorative plugs to cover the outer mounting --..� ��.�� ����,��;����61��������� ��.�;���
<br /> screw holes. All HFP-11 detectors are approved for ��Q��� ��,���,��,�� ����� �������
<br /> operation within the UL specified temperature range �y��j�� ,�p,���;,$;,, q���,�5�� ����
<br /> of 32 to 100 degrees F (0 to 38 degrees C). �;p.H� �r��iy�usin�v�a�t�i�ttA��r�� �
<br /> ' 1r�1� n���t���r
<br /> _
<br /> Application Data ��c�� ��_������rw-s������������������ �►a-��
<br /> �o���� �a������ ������
<br /> Installation of the HFP-11 series of fire detectors �� �;�,������ ��,,;,���a ,���,�,,,� �p�
<br /> requires a two-wire circuit. In many retrofit cases, �� ��„������r,,,; � � �, ��xm�ur� �lo-��p
<br /> existing wiring may be used. "T-tapping" is permitted ;,���� ���ackin ��t�°sar�es�t��cta� ����
<br /> only for Style 4 (Class B) wiring.The HFP-11 is polarity ���.�� ��{,���p�0ir���fre��,c�rc�����orir�r�ar�i h� �r�
<br /> insensitive.This feature can greatly reduce installation ' t�, scr��,�
<br /> an debugging time. HFP-11 fire detectors can be �n�e�e�eor�vr,
<br /> applied within the maximum 30 foot center spacing �F�tt� �ddr�ssat;�Frre�irnF�r�a�a.s�r��) ��-o�a��
<br /> _ _
<br /> (900 sq. ft. areas) as referenced in NFPA 72.This ��-t��G r��ra�aurnin �as��nr�c�stt�u��i ����
<br /> __
<br /> applications guideline is based on ideal conditions, ,�a-1�p� ���tHau�in #u�.c9 �t�-
<br /> specifically, smooth ceiling surfaces, minimal air ��-N�C ����a��t:nr�r�st�Irn��i�tt���taf�tu�.GE �t���..�
<br /> movement, and no physical obstructions between �st���-�t� d�a�it��s�se°nr�r�sit�r�r�i�n��ec�cr�rrll4,�� �i����
<br /> potential fire sources and the detector. Do not mount
<br /> detectors in close proximity to ventilation or heating
<br /> and air conditioning outlets. Exposed joints or beamed
<br />
|