Laserfiche WebLink
INSTALLATION AND MAINTENANCE INSTRUCTIONS �� �, <br /> Q Game�n�ell � <br /> � <br /> �FIRE CONTROL w <br /> INSTRUMENTS o <br /> 0 <br /> by Honeywell j <br /> V@IOCI t%TM Series �2 Clintonville Road,Northford,cT oc4�z <br /> AMM-4F Monitor Module c203)484-7161;Fax: (203)484-7118 <br /> Specifications <br /> Normal Operating Voltage: 15 to 32 VDC <br /> Maximum Current Draw: 5.0 mA(LED on) <br /> Average Operating Current: 375}iA (Group Poll);350µA(Direct Poll);GOOpA;(communicating[DC shorted) <br /> EOL Resistance: 47K Ohms <br /> Maximum IDC Wiring Resistance: 1,500 Ohms <br /> Maximum IDC Voltage: 11 Volts <br /> Mascimum IDC Current: 450pA <br /> Temperature Range: 32°F to 120°F(0°C to 49°C) <br /> Humidity: 10% to 93% Non-condensing <br /> Dimensions: 4�/z"H x 4"W x 1'/a"D (Mounts to a 4"square by 2'/s"deep box.) <br /> Accessories: SMB500 Electrical Box <br /> BEFORE INSTALLING MOUNTIN6 <br /> This information is included as a quick reference installation guide.Refer to The AMM-4F mounts directiy to 4-inch square electrical boxes(see Figure 2). <br /> the wntrol panel installation manuai for detailed system informatioi�. If the The box must have a minimum depth of 2'/s inches.Surface mounted electri- <br /> modules will be installed in an existing operational system,inform the opera- cal boxes(SMB500j are availabfe from Gamewell-FCI. <br /> tor and local authoriry that the system will be temporarily out of service.Dis- FIGURE 2.MODULE MOUNTING: <br /> connect power to the wntrol panel before installing the modules. <br /> NOTE:For UI.Listed security installations,the AMM-4F must be mounted <br /> NO'TICE:This manual should be left with the owner/user of this equipment. within the control panel enclosura <br /> GENERAL DESCRIPTtON <br /> The AMM-4F Moni[or Module is intended for use in intelligent,two-wire sys- �� <br /> tems,where the individual address of each module is selected using the built- � `@ <br /> in rotary switches.it provides either a 2-wire or 4-wire fault tolerantinitiating m�, ^ � � <br /> device circuit(IDC)for normally open cmrtact fire alarm and supervisory de- � � �. �if' <br /> vices,or either normally open or normally closed security devices.The mod- � `,�i / <br /> ule has a panel controlled LED indicator. ,� � <br /> COMPATIBILITY REQUIREMENTS <br /> To ensure proper operation,this module shall be connected to a compatible <br /> Gamewell-FCI system control panel (list availabie from Gamewell-PCI). _�� I � (� \ <br /> FIGURE 1.CONTROL AND INDICATORS: 8 B �� ISOLATED <br /> I QUADRANT <br /> � I <br /> � � O O � ' o0 <br /> o e o <br /> T99 Q � � �� <br /> � � <br /> T10 Ti <br /> T9 TZ C1066-00 <br /> WIRING <br /> T8 T3 NOTE: All wiring must conform to applicable local codes, ordinances, and <br /> regulations.This module is intended for power limited wiring only. <br /> T7 56�8 9� 56�8 9 T 1. Install module wiring in acwrdance with the job drawings and appropri- <br /> Ts 4 0 11 4 T5 ate wiring diagrams. <br /> 3 12 3 ° 2. Set the address on the module per job drawings. <br /> 2�0£� 2�0 3. Secure module to electrical box(supplied by instailer),shown in Figure 2. <br /> � TENS 9 OI�ES � <br /> Q❑O D❑ <br /> LOOP ADORES <br /> C1067-00 <br /> 9000-0589 1 I56-3553-001 <br />