3402 MCDOUGALL AVE SNO CO PW 2018-11-14

� • • � ' � • • 2015 WSEC Compliance Forms for Commercial Buildings inGuding R2,R3.&R4 over 3 stories and all R1 Revised Jun 2016 Project Title: Seaway Transit Center-Comfort Station Date 02/13/2017 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy Code,Commercial Provisions. Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes SCOPE Low energy spaces are identified on plans;include project information, na C402.1.1 Low energy spaces and calculations if applicable,that demonstrate spaces are eligible for envelope provisions exemption r�n C402.1.1.1 Semi-heated spaces Semi-heated spaces are identified on plans,include calculations that demonstrate spaces are eligible for wall insulation exemption Provide building area,average wall and roof U-factor,and installed n�= C402.12 Equipment Buildings equipment information that demonstrates equipment building is eligible for envelope provision exemption Walk-in and Cooler and freezer spaces are identified on plans;C410 envelope �3 C410.2 warehouse cooler compliance forms provided(pending) and freezer spaces -�a C101.4.1 Mixed occupancy Spaces with different occupancy requirements are identified on plans Existing unconditioned spaces changing to semi-heated or conditioned -��- C503.2 Change of space space,and existing semi-heated spaces changing to conditioned space, conditioning are identified on plans.Include calculations that demonstrate baseline and final level of conditioning. Existing F,S and U-occupancy spaces undergoing a change in occupancy are indicated on plans;include calculations that demonstrate upgrade complies with the current WSEC. Change of Pre-2002 Group R spaces undergoing a change to a commercial na C505.1 occupancy are indicated on plans;include calculations that demonstrate occupancy upgrade complies with the current WSEC. Non-Group R occupancy spaces undergoing a change to Group R are indicated on plans;include calculations that demonstrate upgrade complies with the current WSEC. ENVELOPE PROVISIONS Indicate envelope insulation compliance path and provide applicable C103.2 Compliance forms;ENV-PRESCRIPTIVE or ENV-UA/ENV-SHGC for component " � C103.6.3 documentation Performance _ ATTACHED If complying via total buidling performance,provide a list of all proposed envelope component types,areas and U-values C303.1.1 Insulation Indicate identification mark shall be applied to all insulation materials and C303.12 identification insulation installed such that the mark is readily observable during inspection IN SPECS C303.1.3 Fenestration product Fenestration products shall be labeled with rated U-factor,SHGC,VT,and }��r C402.4.3 rating leakage rating IN SPECS Indicate installation methods,thicknesses,densities and clearances to C303.1.1 General insulation achfeve the intended R-value of all insulation materials; Y�y C402.2.1 installation Where two or more layers of rigid insulation will be used,indicate that edge joints between layers are staggered A2.6 Indicate R-value(s)of cavity/continuous insulation on roof sections; Indicate framing materials on roof sections; Indicate method of framing for ceilings below vented attics and vaulted ceilings per A102.2(std,adv); C103.2 Roof assembly Provide area weighted average U-factor calculation for insulation whose � � C402.2.2 insulation thickness varies by 1 inch or less: Indicate effective U-factors of tapered insulation entirely above deck per A1022.6;include roof configuration and slope,maximum R-value at peak and minimum R-value at low point for all roof surfaces Indicate R-values for thermal spacers and each insulation layer,and liner system(LS)method for metal building roofs A2.4-A2.7 na C40222 Skylight curb Indicate curb insulation R-value on roof section if not included in skylight insulation NFRC rating Indicate R-value(s)of cavity/continuous insulation on wall sections; Indicate framing materials on wall sections; Indicate method of framing for wood const per A1032(std,int,adv); C1032 Indicate material density category,wall weight and heat capacity for ,E , C4022.3 Above/below grade qualifying mass walls; ' C4022.4 wall insulation C3032.1 For qualifying ASTM C90 masonry walls.indicate loose-fill core insulation material and percentage of cores filled including grouted cores,bond beams.vertical fills.headers and any other grouted cores; Indicate method of protection of exposed exterior basemenUcrawlspace wall insulation A2.4-A2.7