3402 MCDOUGALL AVE SNO CO PW 2018-11-14

� � • � ' � • • 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 PfOJ2C1 TIYI2: Seaway Transit Center - Comfort Station Date Q2�13�2017 Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes C1032 Indicate rated U-factor(swinging)or R-value(non-swinging-roll- yes Opaque doors up/sliding)on wall sections or in door schedules-applies to doors with C402.4.4 less than 50%glazed area A2.3 Floor over outdoor or Indicate R-value(s)of cavity/continuous insulation on floor sections; na C4022.5 unconditioned space Indicate framing material on floor sections; insulation Indicate material density category and weight of qualifying mass floors Indicate R-value of continuous insulation on wall section or foundation detail, C4022.6 Slab-on-grade floor �ndicate insulation extends down vertically and/or horizontally the required C3032.1 insulation distance from top of slab; Indicate method of protection of exposed exterior slab edge insulation 2/A2.4 Indicate R-value of continuous insulation on wall section or foundation Radiantly heated detail; C4022 6 slab-on-grade floor Indicate insulation extends down vertically from top of slab and then C30321 insulation horizontally under the entire slab; Indicate method of protection of exposed exterior slab edge insulation Radiant heating Indicate insulation R-value behind radiant panels,U-bend/headers and �. C4022.8 system insulation bottom surface of radiantly heated floors(other than radiantly heated slab- on-grade) C402.4.1 Vertical fenestration Provide calculation for total vertical fenestration area as a percentage of -_ C5022.1 gross above grade wall area(WWR)for new construction,additions and C503.3.2 maximum area alterations In ENV-SUM A2.3 Provide calculations showing that the percentage of overall conditioned floor area within daylight zones is equal to or greater than 50%in 1 &2 story builidngs:OR Provide calculations showing that the percentage of overall net floor area Increased Within daylight zones is equal to or greater than 25%in buildings 3 stories C402 4.1.1 prescriptive or more;include the gross floor area and list of spaces omitted for the net C4052 4.1 maximum vertical floor area: C5022.1 fenestration area C503.32 with daylight zones Note in envelope plans that all lighting fixtures located within daylight and controls zones shall be provided with daylight responsive controls per WSEC Section C405.2.4.1;indicate method of control in lighting fixture schedules Indicate that the VT of vertical fenestration is at least 1.1 times the rated SHGC Indicate high performance U-factors and SHGC values in fenestration C402.41.3 prescriptive schedules; r.a C5022 1 maximum vertical fenestration area �f applicable,provide area-weighted U-factor calculation(s)used for C503.32 N,ith high- multiple fenestration elements within the same fenestration category per Table C402.3 Increased prescriptive Indicate that for eligibility,all occupied,conditioned spaces will be served c� C402.4.1 4 maximum vertical by a dedicated outside air system(DOAS)that delivers ventilation air C403.6 fenestration area without requiring operation of the heating/cooling system per Section with DOAS C403.6 mechanical systems Wall/vertical Indicate if component performance with target area adjustment will be no C402.1.5 fenestration target used to account for vertical fenestration area in excess of the prescriptive area adjustment maximum allowed C402.4.1 Skylight maximum Provide calculation for total skylight area as a percentage of gross roof na C502.22 area area(SRR)for new construction,additions and alterations in ENV-SUM C503.3.3 Roof/skylight target Indicate if component performance with target area adjustment will be ,�a C402.1.5.2 used to account for skylight area in excess of the prescriptive maximum area adjustment allowed Indicate U-factors,SHGC and VT values in fenestration schedules; U-factors,SHGC If applicable,provide area-weighted U-factor calculation(s)used for ,_ C402.4.3 and VT for all multiple fenestration elements within the same fenestration category per ' C303.1.3 fenestration Table C402.3 assemblies Indicate if values are NFRC or default;if default then specify frame type, glazing layers.gap width,low-e coatings,gas-fill A2.3 Permanent shading For windows with overhangs or permanent projection shading devices, n<� C402.4.3 provide projection factor calculations(Equation C4-6)and associated devices minimum SHGC for north and non-north orientations