615 80TH ST SW 2022-01-03 - Laserfiche WebLink

Building Permitf • 2012 Washington State Energy Code Compliance forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Project Tide: POCOCK RACING SHELL ADDITION Date 12/15/2016 Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes C103.2 Indicate rated U-factor (swinging) or R-value (non -swinging - roll-upfsliding) e.. C402.4.4 Opaque doors on wall sections or in door schedules - applies to doors with less than 50% glazed area Floor over outdoor or Indicate R-value(s) of cavity/continuous insulation on floor sections; indicate framing material on floor sections; Y- C402.2.5 unconditioned space insulation Indicate material density category and weight of qualifying mass floors Indicate R-value of continuous insulation on wall section or foundation detail; C402.2.6 Ssulati grade floor Indicate insulation extends down vertically and/or horizontally the required C303.2.1 insulation distance from top of slab; Indicate method of protection of exposed exterior slab edge insulation Indicate R-value of continuous insulation on wall section or foundation Radiantly heated slab detail; nG C402.2.6 C303.2.1 on -grade floor Indicate Insulation extends down vertically from top of slab and then insulation horizontally under the entire slab; _ Indicate method of protection of exposed exterior slab edge insulation Radiant heating Indicate insulation R-value behind radiant panels, U-bendlheaders and na C402.2.8 system insulation bottom surface of radiantly heated floors (other than radiantly heated slab - on -grade) C402:4.1 Vertical fenestration Provide calculation for total vertical fenestration area as a percentage of na C502.2.1 gross above grade wall area (WWR) for new construction, additions and C503.3.2 maximum area alterations In ENV -SUM Provide calculations showing that the percentage of overall conditioned floor area within daylight zones is equal to or greater than 50% in 1 & 2 story builidngs: OR Provide calculations showing that the percentage of overall net floor area C40 2.4.1 .1 1.1 Increased prescriptive within daylight zones is equal to or greater than 25% in buildings 3 stories or C402A maximum vertical more; include the gross floor area and list of spaces omitted for the net floor na C502.2.1 fenestration area with C503.3.2 daylight zones and Noe in envelope plans that all lighting fixtures located within daylight zones controls shall be provided with daylight responsive controls per WSEC Section C405.2.4.1; indicate method of control in lighting fixture schedules Indicate that the VT of vertical fenestration is at least 1.1 times the rated SHGC Indicate high performance U-factors and SHGC values in fenestration C402.4.1.3 prescriptive schedules; na C502.2.1 maximum vertical fenestration area with if applicable, provide area -weighted U-factor caiculation(s) used for multiple C503.3.2 high-performance fenestration elements within the same fenestration category per Table C402.3 Increased C402.4.1.4 prescriptive maximum vertical Indicate that for eligibility, all occupied, conditioned spaces will be served by na C403.6 fenestration area with a dedicated outside air system (DOAS) that delivers ventilation airwithout DOAS mechanical requiring operation of the heating/cooling system per Section C403.6 systems Wall/vertical Indicate if component performance with target area adjustmentwill be used nu C402.1.5 fenestration target to account for vertical fenestration' area in excess of the prescriptive area adjustment maximum allowed na C402.4.1 C502.2.2 Skylight maximum Provide calculation for total skylight area as a percentage of gross roof area C503.3:3 area (SRR) for new construction, additions and alterations in ENV -SUM na C402.1.5.2 Roof/skylight target Indicate if component performance with target area adjustment will be used area adjustment to account for skylight area in excess of the prescriptive maximum allowed Indicate U-factors, SHGC and VT values in fenestration schedules; U-factors, SHGC and If applicable, provide area -weighted U-factor calculation(s) used for multiple na C402.4.3 VT for all fenestration fenestration elements within the same fenestration category per Table C303.1.3 assemblies C402.3 Indicate if values are NFRC or default; If default then specify frame type, glazing layers, gap width, low-e coatings, gas -fill shading For windows with overhangs or permanent projection shading devices, na C402.4.3 JPermanent devices provide projection factor calculations (Equation C4-6) and associated minimum SHGC for north and non -north orientations