824 W CASINO RD BASE FILE 2018-12-27

I Building Permit Plans Checklist, pg. 2 ENV-CHK 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Project Title: Avaire Apartments Renovation Date 03/30/2017 Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes 0103.2 Indicate rated U-factor(swinging)or R-value(non-swinging-roll- yes Opaque doors up/sliding)on wall sections or in door schedules-applies to doors with 0402.4.4 less than 50%glazed area A6.1 No Floor over outdoor or Indicate R-value(s)of cavity/continuous insulation on floor sections; No C402.2.5 unconditioned space Indicate framing material on floor sections; No insulation Indicate material density category and weight of qualifying mass floors no Indicate R-value of continuous insulation on wall section or foundation detail; C402.2.6 Slab-on-grade floor Indicate insulation extends down vertically and/or horizontally the required no C303.2.1 insulation distance from top of slab; no Indicate method of protection of exposed exterior slab edge insulation No Indicate R-value of continuous insulation on wall section or foundation Radiantly heated detail; C402.2.6 slab-on-grade floor Indicate insulation extends down vertically from top of slab and then No C303.2.1 insulation horizontally under the entire slab; No Indicate method of protection of exposed exterior slab edge insulation Radiant heating Indicate insulation R-value behind radiant panels,U-bend/headers and No C402.2.8 system insulation bottom surface of radiantly heated floors(other than radiantly heated slab- on-grade) C402.4.1 Provide calculation for total vertical fenestration area as a percentage of Vertical fenestration yes 0502.2.1 maximum area gross above grade wall area(WWR)for new construction,additions and 0503.3.2 alterations In ENV-SUM ENV-SUM Provide calculations showing that the percentage of overall conditioned No" floor area within daylight zones is equal to or greater than 50%in 1&2 story builidngs:OR Provide calculations showing that the percentage of overall net floor area Increased within daylight zones is equal to or greater than 25%in buildings 3 stories No C402.4.1.1 prescriptive or more;include the gross floor area and list of spaces omitted for the net 0405.2.4.1 maximum vertical floor area; 0502.2.1 fenestration area C503.3.2 with daylight zones Note in envelope plans that all lighting fixtures located within daylight and controls zones shall be provided with daylight responsive controls per WSEC No Section 0405.2.4.1;indicate method of control in lighting fixture schedules No Indicate that the VT of vertical fenestration is at least 1.1 times the rated SHGC increasea Indicate high performance U-factors and SHGC values in fenestration No prescriptive 0402.4.1.3 schedules; maximum vertical C502.2.1 fenestration area If applicable,provide area-weighted U-factor used for No 0503.3.2 with high- multiple fenestration elements within the same fenestration category per nerfnrmanna nla7inn Table 0402.3 Increased prescriptive Indicate that for eligibility,all occupied,conditioned spaces will be served No C402.4.1.4 maximum vertical by a dedicated outside air system(DOAS)that delivers ventilation air C403.6 fenestration area without requiring operation of the heating/cooling system per Section with DOAS C403.6 mechanical systems Wall/vertical Indicate if component performance with target area adjustment will be No 0402.1.5 fenestration target used to account for vertical fenestration area in excess of the prescriptive area adjustment maximum allowed C402.4.1 Skylight maximum Provide calculation for total skylight area as a percentage of gross roof No 0502.2.2 0503.3.3 area area(SRR)for new construction,additions and alterations in ENV-SUM Roof/skylight target Indicate if component performance with target area adjustment will be No 0402.1.5.2 used to account for skylight area in excess of the prescriptive maximum area adjustment allowed no Indicate U-factors,SHGC and VT values in fenestration schedules; U-factors,SHGC If applicable,provide area-weighted U-factor calculation(s)used for No C402.4.3 and VT for all multiple fenestration elements within the same fenestration category per 0303.1.3 fenestration Table C402.3 assemblies Indicate if values are NFRC or default;if default then specify frame type, yes glazing layers,gap width,low-e coatings,gas-fill A6.1 Permanent shading For windows with overhangs or permanent projection shading devices, No C402.4.3 devices provide projection factor calculations(Equation C4-6)and associated minimum SHGC for north and non-north orientations #/1)))