3625 8TH ST 2019-01-18 - Laserfiche WebLink

• , F 4 Building Permit Plans Checklist, pg. 2 ENV-CHK • 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all Ri Project Title: cRossoocK FACILITY Date 12/29/2016 Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes 0103.2 Indicate rated U-factor(swinging)or R-value(non-swinging-roll- yes 0402.4.4 Opaque doors up/sliding)on wall sections or in door schedules-applies to doors with Al.11,A3.00, less than 50%glazed area A3.01 Floor over outdoor or Indicate R-value(s)of cavity/continuous insulation on floor sections; na C402.2.5 unconditioned space Indicate framing material on floor sections; insulation Indicate material density category and weight of qualifying mass floors Indicate R-value of continuous insulation on wall section or foundation detail; yes 0402.2.6 Slab-on-grade floor Indicate insulation extends down vertically and/or horizontally the required 0303.2.1 insulation distance from top of slab; Indicate method of protection of exposed exterior slab edge insulation A3.16,Spec's . Indicate R-value of continuous insulation on wall section or foundation Radiantly heated detail; na 0402.2.6 slab-on-grade floor Indicate insulation extends down vertically from top of slab and then 0303.2.1 insulation horizontally under the entire slab; Indicate method of protection of exposed exterior slab edge insulation Radiant heating Indicate insulation R-value behind radiant panels,U-bend/headers and na C402.2.8 system insulation bottom surface of radiantly heated floors(other than radiantly heated slab- on-grade) 0402.4.1 Vertical fenestration Provide calculation for total vertical fenestration area as a percentage of yes 0502.2.1 gross above grade wall area(WWR)for new construction,additions and A2.01,A3.00, 0503.3.2 maximum area alterations In ENV-SUM A3.01 • Provide calculations showing that the percentage of overall conditioned floor area within daylight zones is equal to or greater than 50%in 1 &2 story builidngs:OR Provide calculations showing that the percentage of overall net floor area Increased within daylight zones is equal to or greater than 25%in buildings 3 stories 0402.4.1.1 prescriptive or more;include the gross floor area and list of spaces omitted for the net na 0405.2.4.1 maximum vertical floor area; 0502.2.1 fenestration area Note in envelope plans that all lighting fixtures located within daylight 0503.3.2 with daylight zones zones shall be provided with daylight responsive controls per WSEC and controls Section C405.2.4.1;indicate method of control in lighting fixture schedules Indicate that the VT of vertical fenestration is at least 1.1 times the rated SHGC Increased Indicate high performance U-factors and SHGC values in fenestration 0402.4.1.3 prescriptive schedules; na 0502.2.1 maximum vertical If applicable,provide area-weighted U-factor calculation(s)used for C503.3.2 fenestration area multiple fenestration elements within the same fenestration category per with high- Table C402.3 nerfnrmanna nla7inn Increased prescriptive Indicate that for eligibility,all occupied,conditioned spaces will be served C402.4.1.4 maximum vertical by a dedicated outside air system(DOAS)that delivers ventilation air na C403.6 fenestration area without requiring operation of the heating/cooling system per Section with DOAS 0403.6 mechanical systems Wall/vertical Indicate if component performance with target area adjustment will be na 0402.1.5 fenestration target used to account for vertical fenestration area in excess of the prescriptive area adjustment maximum allowed • 0402.4.1 Skylight maximum Provide calculation for total skylight area as a percentage of gross roof na 0502.2.2 area area(SRR)for new construction,additions and alterations in ENV-SUM 0503.3.3 Roof/skylight target Indicate if component performance with target area adjustment will be na 0402.1.5.2 used to account for skylight area in excess of the prescriptive maximum area adjustment allowed • Indicate U-factors,SHGC and VT values in fenestration schedules; U-factors,SHGC If applicable,provide area-weighted U-factor calculation(s)used for 0402.4.3 and VT for all multiple fenestration elements within the same fenestration category per yes 0303.1.3 fenestration Table 0402.3 assemblies Indicate if values are NFRC or default;if default then specify frame type, glazing layers,gap width;low-e coatings,gas-fill Spec's Permanent shading For windows with overhangs or permanent projection shading devices, yes C402.4.3 provide projection factor calculations(Equation C4-6)and associated devices minimum SHGC for north and non-north orientations 6/A2.01