3625 8TH ST 2019-01-18 - Laserfiche WebLink

Building Permit Plans Checklist, pg. 1 ENV-CHK 2015 WSEC Compliance Forms for Commercial Buildings including R2,R3,&R4 over 3 stories and all R1 Revised Jun 2016 Project Title: CROSSDOCK FACILITY Date 12/29/2016 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy Code,Commercial Provisions. Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes SCOPE Low energy spaces are identified on plans;include project information, na 0402.1.1 Low energy spaces and calculations if applicable,that demonstrate spaces are eligible for envelope provisions exemption na 0402.1.1.1 Semi heated spaces Semi-heated spaces are identified on plans,include calculations that demonstrate spaces are eligible for wall insulation exemption Provide building area,average wall and roof U-factor,and installed na 0402.1.2 Equipment Buildings equipment information that demonstrates equipment building is eligible for envelope provision exemption • Walk-in and Cooler and freezer spaces are identified on plans;C410 envelope • na 0410.2 warehouse cooler and freezer spaces compliance forms provided(pending) yes C101.4.1 Mixed occupancy Spaces with different occupancy requirements are identified on plans Cover Sheet Existing unconditioned spaces changing to semi-heated or conditioned na 0503.2 Change of space space,and existing semi-heated spaces changing to conditioned space, conditioning are identified on plans.Include calculations that demonstrate baseline and final level of conditioning. Existing F,S and U-occupancy spaces undergoing a change in occupancy are indicated on plans;include calculations that demonstrate upgrade complies with the current WSEC. • Change of Pre-2002 Group R spaces undergoing a change to a commercial na C505.1 occupancy are indicated on plans;include calculations that demonstrate occupancy upgrade complies with the current WSEC. Non-Group R occupancy spaces undergoing a change to Group R are indicated on plans;include calculations that demonstrate upgrade complies with the current WSEC. ENVELOPE PROVISIONS Indicate envelope insulation compliance path and provide applicable 0103.2 Compliance forms;ENV-PRESCRIPTIVE or ENV-UA/ENV-SHGC for component Separate yes 0103.6.3 documentation performance ENV-UA If complying via total buidling performance,provide a list of all proposed Document envelope component types,areas and U-values 0303.1.1 Insulation Indicate identification mark shall be applied to all insulation materials and yes insulation installed such that the mark is readily observable during A1.11,A3.05, C303.1.2 identification inspection Spec's 0303.1.3 Fenestration product Fenestration products shall be labeled with rated U-factor,SHGC,VT,and yes 0402.4.3 rating leakage rating Spec's Indicate installation methods,thicknesses,densities and clearances to 0303.1.1 General insulation achieve the intended R-value of all insulation materials; yes 0402.2.1 installation Where two or more layers of rigid insulation will be used,indicate that A1.11,A3.05, edge joints between layers are staggered - Spec's Indicate R-value(s)of cavity/continuous insulation on roof sections; Indicate framing materials on roof sections; Indicate method of framing for ceilings below vented attics and vaulted ceilings per A102.2(std,adv); C103.2 Roof assembly Provide area weighted average U-factor calculation for insulation whose yes 0402.2.2 insulation thickness varies by 1 inch or less; Indicate effective U-factors of tapered insulation entirely above deck per A102.2.6;include roof configuration and slope,maximum R-value at peak and minimum R-value at low point for all roof surfaces Indicate R-values for thermal spacers and each insulation layer,and liner system(LS)method for metal building roofs A3.16,Spec's na 0402.2.2 Skylight curb Indicate curb insulation R-value on root section if not included in skylight insulation NFRC rating • Indicate R-value(s)of cavity/continuous insulation on wall sections; Indicate framing materials on wall sections; Indicate method of framing for wood const per A103.2(std,int,adv); C103.2 Indicate material density category,wall weight and heat capacity for yes 0402.2.3 Above/below grade qualifying mass walls; 0402.2.4 wall insulation C303.2.1 For qualifying ASTM 090 masonry walls,indicate loose-fill core insulation material and percentage of cores filled including grouted cores,bond beams,vertical fills,headers and any other grouted cores; Indicate method of protection of exposed exterior basement/crawlspace wall insulation A3.16,Spec's J 3