2714 COLBY AVE 2017 ROMIOS PIZZA Plans 2022-12-02

TABLE C402.4 C402.4.1.1 Increased vertical fenestration area : BUILDING ENVELOPE FENESTRATION with daylight responsive controls.A maximum of : MAXIMUM U-FACTOR AND SHGC 40 percent ofthe gross above-grade wall area shall be : REQUIREMENTS permitted to be vertical fenestration for the purpose : of prescriptive compliance with Section C402.1.4 or : CLIMATE 5 AND MARINE 4 for the component performance alternative in Section : ZONE C402.1.5,provided all of the following requirements : Vertical Fenestration are met: : 1. In buildings not greater than two stories above (I-factor grade,no less than 50 percent of the conditioned Nonmetal framing floor area is within a daylight zone. (all)a 0.30 2. In buildings three or more stories above grade, Metal framing not less than 25 percent of the net floor area is (fixed)e 038 within a daylight zone. Metal framing 3. Daylight responsive controls complying with (operable)` 0.40 Section C405.2.4.1 are installed in daylight zones. Metal framing 0.60 4. Visible transmitCance(V'1�of vertical (entrance doors)d fenestration is greater than or equal to 1.1 times SHGC solar heat gain coefftcient(SHGC). Exception:Fenestration that is outside the scope of Orientation SEW N NFRC 200 is not required to comply with Item 4. C402.4.1.2 Reserved. • PF<0.2 0.40 0.53 � C402.4.1.3 Increased vertical fenestration area with • � 0.2<PF<0.5 0.48 0.58 high-performance jenestration.The vertical . fenestration area(not including opaque doors and : PF>0.5 0.64 0.64 opaque spandrel panels)is permitted to exceed 30%but : shall not exceed 40%of the gross above grade wall area, : Skylights for the purpose of prescriptive compliance with Section : C402.1.3 provided that each of the following conditions : U-factor 0.50 are met: : 1. The vertical fenestration shall have the following SHGC 0.3 5 tJ-factors: a. Non-metal framing(all)=0.28 NR= No requirement. b. Meta1 framing(fixed)=0.34 a. °Nonmetal framing"includes framing materials other a Metal framing(operable)=0.36 than metal,with or without metal reinforcing or d. Metal framing(entrance doors)=0.60 cladding. 2. The SHGC of the vertical fenestration shall be Iess b. "Metal framing"includes metal framing,with or than or equal to 0.35,adjusted for projection factor without thermal break. "Fixed"includes curtain wall, in compliance with C402.43. storefront,picture windows,and other fixed windows. An area-weighted average shall be permitted to satisfy ■ c. °Nletal framing"includes meta]framing,with or without the U-factor requirement for each fenestration product : thermal break."Operable"includes openable category listed in Item i of this section. Individual . fenestration products other than"entrance doors.° fenestration products from different fenestration product : d. "Metal framing"includes metal framing,with or without categories shall not be combined in calculating the � thermal break."Entrance door"includes glazed swinging area-weighted average U-factor. ■ entrance doors.Other doors which are not entrance The compliance path described in this section is not ■ doars,including sliding glass doors,are considered permitted to be used for the Total Building Performance : "operable." compliance path in Section C407.The compliance path : described in this section is permitted to be used for the : C402.41 Maximum area.The vertical fenestration component performance alternative in Section : area(not including opaque doors and opaque spandrel C402.1.5,provided that the requirements of Section : panels)shall not exceed 30 percent of the gross C402.1.5 are met. : above-grade wall area. The skylight area shall not exceed 3 percent of the gross roof area. 2015 Washington State Energy Code CE-29