2714 COLBY AVE 2017 ROMIOS PIZZA Plans 2022-12-02

GLASS AND GLAZING destroyed. A label meeting the requirements of this section is less than 60 inches (1524 mm) above the walking sur- shall be permitted in lieu of the mattufacturer's designatiott. face shall be considered a hazardous location. Exceptions: Exceptions: 1. For other than tempered glass,manufacturer's desig- 1. Decorative glazing. nations are not zequired, provided the building offi- 2, Where there is an intervening wall or other per- cial approves the use of a certificate, affidavit or manent barrier between the door and glazing. other evidence confirming compliance with this code. 3. Where access through the door is to a closet or 2. Tempered spandrel glass is permitted to be identi- storage area 3 feet (914 mm) or less in depth. fied by the manufacturer with a removable paper Glazing in this application shall comply with Section 2406.43. designation. 2406.3.1 Multipane assemblies.Multipane glazed assem- 4. Glazing in walls on the latch side of and perpen- dicular to the plane of the door in a closed posi- blies ha2 ing individual panes not exceeding 1 square foot tion in one- and two-family dwellings or within (0.09 m) in exposed areas shall have at least one pane in dwelling units in Group R-2. the assembly marked as indicated in Secrion 2406.3.Other panes in the assembly shall be marked "CPSC 16 CFR 2406.4.3 Glazing in windows. Glazing in an individual Part 1201"or"ANSI Z97.1,"as appropriate. fixed or operable panel that meets all of the following con- ditions shall be considered a hazardous location: 2406.4 Hazardous locations.T'he locations specified in Sec- tions 2406.4.1 through 2406.4.7 shall be considered specific 1. The exposed area of an Zndividual pane is greater hazardous locations requiring safety glazing materials. than 9 square feet(0.84 m). 2406.4.1 Glazing in doors.Glazing in all fixed and opera- 2• The bottom edge of tl�e glazing is less than 18 inches ble panels of swinging, sliding and bifold doors shall be (457 mm)above the floor. considered a hazardous location. 3. The top edge of the glazing is greater than 36 inches Exceptions: (914 mm)above tt�e floor. 1. Glazed openings of a size through which a 3- 4. One or more walking surface(s)are within 36 inches inch-diameter(76 mm)sphere is unable to pass. (914 mm}, measured horizontally and in a straight line,of the plane of the glazing. 2. Decorative glazing. Exceptions• 3. Glazing materials used as curved glazed panels in � revolving doors. 1. Decorative glazing. 4. Commercial refrigerated cabinet glazed doors. 2• Where a horizontal rail is installed on the accessi- ble side(s) of the glazing 34 to 38 inches (864 to 2406.4.2 Glazing adjacent to doors. Glazing in an indi- 965 mm) above the walking surface. The rail vidual fixed or operable panel adjacent to a door where the shall be capable of withstanding a horizontal load nearest vertical edge of the glazing is within a 24-inch of 50 pounds per linear foot (730 N/m) without (610 mm)arc of either vertical edge of the dooz in a closed contacting the glass and be a minimuzn of 11/2 position and where the bottom exposed edge of the glazing inches(38 mm)in cross-sectional height. TABLE 2406.2(1) MINIMUM CATEGORY CLASSIFICATION OF GLA2ING USING CPSC 16 CFR PART 1201 GLAZING IN DOORS AND GLAZED PANELS GLAZED PANELS EXPOSED SURFACE STORM OR GLAZING IN DOORS REGULATED BY REGULATED BY ENCLOSURES SLIDING GLASS AREA OF ONE SIDE OF COMBINATION REGULATED BY DOORS PATIO TYPE ONE LITE DOORS (Category class) SECTION 2406.4.3 SECTION 2406.4.2 SECTION 2406.4.5 (Category class) (Category class) (Category class) (Category class) �Category class) 9 square feet or less I I No requirement I II II More than 9 square feet II II II II II II For SI: 1 squaze foot=0.0929 mZ. TABLE 24062(2) MINIMUM CATEGORY CLASSIFICATION OF GLAZING USING ANSI Z97.1 EXPOSED SURFACE AREA OF ONE GLAZED PANELS REGULATED BY GLAZED PANELS REGULATED 8Y DOORS AND ENCLOSURES e SIDE OF ONE LITE SECTION 2406.4.3(Category class) SECTION 2406.4.2(Category class) REGULATED BY SECTION 2406.4.5 (Category class) 9 square feei or less No requirement B A More than 9 square feet A A A For SI: square foot=0.0929 m2. a. Use is only permitted by the exception to Section 2406.2. 2015 INTERNATIONAL BUILDING CODE° 545