3301 SEAWAY BLVD BLDG B 2016 Plans 2022-11-29

302/303 FLOOR SURFA�ES � CHANGES IN LEllE1 404 DOORS c�ontinued 502/503 PARKING AND PA�R LQADING ZONfS c�ntinued 604 WATER CLOSEIS � TOILET C061PAFi'iM1EM'S continued 609 GRAB BARS 703 SIGNAI� continued � ANSI 303 - CHANGES IN LEVEL (REFERENCE DETAIL. 5.1) ANSI 404.2.6 - DOOR HARDWARE ANSI 502.7 - SIGNAGE (REFERENCE DETAIL 4.8) ANSI 604.10.7 - DISPENSERS (REFERENCE DETAIL 4.16.2) ANSI 609.3.2 - SIZE AND SPACING � A. Changes in level up to 1/4 may be vertical and withaut edge treatment A. Handles, pulls, latches, locks, and other operating devices shall have a shape that is A. Each accessible parking space must have individual vertically mounted or suspended A. Toilet paper dispensers shall be installed on the side wall, and shall be 7"-9" A. Diameter or width of gripping surface shall be 1-1/4" to 1-1/2", or the shape B. Changes in level between 1/4 and 1/2" shall be beveled with a slope no greater easy to grasp with one hand and does not require tight grasping, tight pinching, or sign. Required van accessible spaces must be designated. maximum in front of the water closet measured to the centerline of the dispenser. shall provide an equivalent gripping surface. than 1:2. twisting of the wnst to operate. B. Characters and symbols on such signs shall be located 60" mimmum above the The outlet of the dispenser shall be 15"-48" maximum A.F.F. 1. The space between grab bars and adjacent walls shall be 1-1/2" a. � � � �` � �' �� �, 1. Lever-operated mechanisms, push-type mechanisms, and U-shaped handles are ground. 1. Dispensers that control delivery or do not permit continuous paper flow shall not � � � acceptable designs. be used. ANSI 609.8 - STRUCTURAL STRENGTH � .. .. .. � 2 2. When sliding doors are fully open, operating hardware shall be exposed and usable ANSI 503.5 - VERTICAL CLEARANCE 2. Operable parts shall be operable with one hand and shall not require tight A. Grab bars and mounting devices shall meet the following requirements: �� '� '� ` �� ^� from both sides. A. Provide minimum vertical clearance of 114" at accessible assen er loadin zones ras in inchin or twistin of the wrisl. 609.8 Allowable stresses shall not be exceeded for materials used where a vertical � P 9 9 9 p 9� P 9 9 or horizontal force of 250 Ibs. is a lied at an oint on the rab bar, fastener 3. Hardware required for accessible door passage shall be mounted between 34 and and along at least one vehicle access route from site entrances and exits. 3. The force required to activate operable pa�ts shall be 5 pounds max. PP Y P 9 letter & numbers on signs shall have a width 48" above finished floor. mounting device, or supporting structure, to height ratio of between 3:5 & 1:1 and ANSI 503 - PASSENGER LOADING ZONE ANSI 604.8 - WATER CLOSEfS 1. Shear stress induced by application of 250 Ib. shall be less than allowable shear a stroke - width to height ratio between Detail 5•1 ANSI 404.2.7.1 - DOOR CLOSERS A. Passenger loading zones shall provide an access aisle at least 60` wide and 20 ft A. If toilet stalls are provided, then at least one shall be a standard toilet stall stress for material used. If connection between grab bar and mounting bracket 1:5 & 1:10. Letters and numbers shall be raised ANSI 302.2 - CARPET A. Door closers shall be adjusted so that from an open position of 90 degrees, the long adjacent and parallel to the vehicle pull-up space. If there are curbs between complying with 604.8; where 6 or more stalls are provided in addition to the stall is considered to be fully restrained, then direct and torsional shear stresses shall (� 1/32", upper case, sans serif or simple serif A. Carpet provided on a floor surface shall be securely attached; have a firm pad or time required to move the door to an open position of 12 degrees shall be 5 the access aisle and the vehicle pull-up space, then a curb ramp complying with 4.7 complying with 604.9, at least one stall 36" wide with an outward swinging, be totaled for the combined shear stress, which shall not exceed the allowable v- type and shall be accompanied with backing, or no pad; and have a level loop, textured loop, level cut pile, or level seconds minimum. shall be provided. Vehicle standing spaces and access aisles shall be level with If-closing door and parallel grab bars shall be provided. Water closets in such stalls shear stress. grade 2 Braille, raised characters shall be at cut uncut ile texture. Maximum ile thickness shall be 1 2'. Ex osed ed es of surface slo es not exceedin 1:48 in all directions. shall com I with detail 4.16. 2. Shear force induced in a fastener or mounting device from application of 250 Ib. least 5/8" 3 high plus 1/8" per foot of / p p / p g P 9 PY International Symbol carpet shall be fastened to flaor surfaces and have trim along the exposed edges. ANSI 404.2.7.2 - SPRING HINGES shall be less than allowable lateral load of either the fastener or mounting device viewing distance above 21 feet. A. Door spring hinges shall be adjusted so that from the open position of 70 degrees, GAI.VANIZED MOUNIING BOL15 or the supporting structure, whichever is the smaller allowable ioad. of Accessibility � �' C �'1 I � e G � S ANSI 302.3 - GRATINGS the door shall move to the closed position in 1.5 seconds minimum. � 54" MIN 3. Tensile force induced in a fastener by a direct tension force of 250 Ib. plus the Detail 4.30.1 Detail 4.30.2 A. If gratings are located in walking surfaces or along accessible routes, then they shall - � maximum moment from the application of 250 Ib. shall be less than the have spaces no greater than 1/2" wide in one direction. ANSI 404.2.8 and IBC with WA STATE AMENDMENTS - DOOR OPENING FORCE � 39"-41" allowable withdrawal load between the fastener and the supporting structure. A. The maximum force for ushin or ullin o en a door shall be as follows: "' 609.6 Grab bars shall not rotate within their fittin s 2505 TFiird Avenue B. If gratings have elongated openings, then they shall be placed so that the long P 9 P 9 P 9 ' Light switch $" MAX Suite 324 dimension is er endicular to the dominant direction of travel. 1. �re doors shall have the minimum opening force allowable by the appropriate '� P P administrotive authority. DIS�AABLED -� � 42" MIN 36" MIN. ANSI 609.5 - ELIMINATING HAZARDS TFiermostats, Etc. Seattle, WA 98121 2. Other doors P_�� 24• A. Grab bars and adjacent wall surfaces shall be free of shnrp or abrasive surfaces. Z � a. Exterior hinged, sliding or folding door: 10.0 Ib. max. RE4u�Rm � Locate n�an controls Edges shall be rounded. W � b. Interior hinged doors: 5.0 Ib. max. o ACC�IBIE � o� wfde atde m 4� � � 206_720.7001 phone � � � �� c. Interior sliding or folding doors: 5.0 Ib. max. z , �,., � � 206.720.2949 fax These forces do not apply to the force required to retract latch bolts or disengage � � 'b � ,`,�D > �' '� other devices that ma hold the door in a closed osition. �� PRE-MANUF. SIGN � ? i i m N � z ANSI 305.2 - SIZE AND APPROACH y P b m� 4 DIA SiEEL POST W/ CAP � i ,,�,� �; a LL' �o � o � 7� � _ � � www.craftarchitects.com A. Minimum clear floor space for a wheelchair and occupant shall be 30" wide x 48" ;�.� a, f� J � c� ,n lon . Clear floor s ace shall be centered on the element it serves. o Fl N I S H G R A D E � _ 9 P � \ ANSI 702.1 - GENERAL '' � SET Posf IN CONC. 7' MIN 9" MAX A. When required, visual alarms shall be provided in each of the following areas, as a 5 0 � Detail 4.16.3 �o � C(J(� �� I • �� :. minimum: rest rooms and any other general usage areas (e.g., meeting rooms), Convenience Outlets �I I N4IE:INSTALL SIGN AT ALL ACCESSIBLE PARKING Detail 4.16.2 h a l l w a y s, l o b b i e s, a n d a n y o t h e r a r e a f o r c o m m o n u s e. STJ�LLS. SPAC6 DESIGNATED FOR VAN PARKING Detail 4.30.3 Data, Tel., Etc. �� P�� E� � � ANSI 406 - SLOPE (REFERENCE DETNL 4.7) ', i i ' swu.� w�vE nunmoru� s�N 'vnN ncc�ssie� REFERENCE DEfNL 4.4,1 & 4.4.2 NFPA 72 - AUDIBLE ALARMS A. Slopes of curb ramps shall comply with 406 �}' MOUNTED BELOW. MOUNT ON WALL OF BLDG WHEN B. Maximum slopes of adjoining gutters, road surface immediately adjacent to the curb � �SS�� A. If provided, audible alarms shall produce a sound that exceeds the prevailing ANSI 307 - GENERAL ramp, or accessible route shall not exceed 1:20. Detail 4•8 equivalent sound level in the room or space by at least 15 dba or exceeds any A. Objects projecting from walls (for example, telephones) with their leading edges maximum sound level with a duration of 60 seconds by 5 dba, whichever is louder. � KITCHENS AND I4TCHENETTE'S between 2T-80" above the finished floor shall protrude no more than 4 into walks, ANSI 406.4 - WIDTH (REFERENCE DETAIL 4.7) AI�SI 605 - URINAL.S 8. Sound levels for alarm signals shall not exceed 120 dba. halls, corridars, passageways, or aisles. Freestanding objects mounted on posts or A. The minimum width of a curb ramp shall be 36", exclusive of flared sides. ANSI 804.6.6 - REFRIGERATOR/FREEZER pylons may overhang 17' maximum from 27"-80" above the ground or finished ANSI 605 - URINALS NFPA 72 - VISUAL ALARMS Combination refrigerators and freezers shall have at least 50� of the freezer floor. Protrudin ob'ects shall not reduce the clear width of an accessible route or 602 �INKII�N' FOl1MaNS A. If urinals are rovided, then at least one shall com I with detail 4.18. A. vsual alarm signal oppliances shall be integrated into the building or facility alarm compartment shelves, including the bottom of the freezer 54 inches (1370mm) � 9 1 ANSI 406.3 - SIDES OF CURB RAMPS (REFERENCE DETAIL 4.7) P Py system. If single station audible alarms are provided then single station visual alarm maximum above the floor when the shelves are installed at the maximum heights z maneuvering space. A. If a curb ramp is located where pedestrians must walk across the ramp or where it ANSI 602.1 - GENERAL si nals shall be rovided. is not protected by handrails or guardrails, it shall have flared sides; the maximum A. Accessible drinkin fountains shall com I with Sections 602 and 307. TAS SECTION 4.18.2 - HEIGHT (REFERENCE DETAIL 12.3.1) 9 P possible in the compartment. A clear floor space, positioned for a parallel approach � O 9 PY Ysual Alarm appliances shall have the following features: to the s ace dedicated to a refri erator freezer, shall be rovided. The cente�line of the slope of the flare shall be 1:10 A. Urinals shall be stall-type or wall hung with a tapered, elongated rim at 17' P 9 � P � � � . 1. The lamp shall be a xenon strobe type or equivalent. clear floor s ace shall be offset 24 inches 610 mm maximum from the centerline of � ANSI 602.2 - CLEAR FLOOR SPACE maximum above the finished floor. The rim shall extend a minimum of 14 from the a � � 2. The color shall be clear or nominal white (i.e. unfiltered or clear filtered white the dedicated s ace. 4° MAX. FAR WIDT ANY AMOUNT ' A. A clear floor space complying w/ Section 305, positioned for a forward approach "'°��• li ht P � LOBBY- � Adjoining Slope Shall 9 )• � � � to the drinking fountain, shall be provided. Knee & toe space complying with 3. The maximum ulse duration shall be two-tenths of one second with a maximum .�- Not Exceed 1:20 TAS SECTION 4.18.3 - CLEAR FLOOR SPACE REFERENCE DETAIL 4.18.1 p Z r If x Is less than 48" Section 306 shall be provided. The clear floor space shall be centered on the � � duty cycle of 40%. (The pulse duration is defined as the time interval between � � Then The Slo e Of The Flare Flared side drinking fountain. A. A clear floor space 30' wide by 48" deep minimum shall be provided in front of � � - � � P initial and final oints �f 10% of max si nal gp2 aNING SURF/ICES � MIORK SURFA�CfS Sides Shall Not Exceed 1:1 EXCEPTIONS: urinal to allow forward approach. p 9 � rn Z � 1. Drinking fountains for standing persons. 1. This space shall adjoin or overiap an accessible route. 4. The intensity shall be a minimum of 75 candela. � VJ ♦^ � � " m11� 2. Drinking fountains primarily for children's use. 2. Urinal shields that do not extend beyond the front edge of the urinal rim may be 5. The flash rate shall be a minimum of 1 Hz and a maximum of 3 Hz � V J � � ',�6 6. The a liance shall be laced 80' above the hi hest floor level within the s ace ANSI 902.2 - SEATING � b � q I q 3. In existing building, existing drinking fountains providing a parallel approach provided with 29" clearance between them. PP P 9 p A. If seating spaces for people in wheelchairs are provided at fixed tables or counters, � � com I in w Section 305, centered on the drinkin fountain shall be ermitted. 3. Urinals installed in alcoves dee er than 24 re uire a maneuverin area of at or 6" below the ceiling, whichever is lower. � p y g / 9 p P 9 9 clear floor space of 30" x 48" shall be provided. Floor space shall not overlap Q � Z a. In large rooms and spaces exceeding 100' across, without obstructions 6' � '� 4. Where specifically permitted by the administrative authority, a parallel approach least 36" minimum wide, centered on fixture. re uired knee s ace b more than 19" � � � shall be permitted that replace existing parallel approach drinking fountains. above the finished floor, such as auditoriums, devices may be place around the 4 P y � N � Ramp (1:12 Max. Slope) perimeter, spaced a maximum 100' apart, in lieu of suspending appliances from � •� Shall Have Detectable Warnin s TAS SECTION 4.18.4 - FLUSH CONTROLS (REFERENCE DETAIL 4.18.2) ANSI 902.3 - KNEE SPACE � 9 ANSI 602.3 - OPERABLE PARTS the ceiling. a � Detail 4.4.1 Detail 4.4.2 and contrasting color. A. Controls shall be 44 maximum above the finished floor. A. If seating for people in wheelchairs is provided at fixed tables or counters, knee � A. 0 erable arts shall com I with Section 309. 7. In general, no place in any room or space shall be more than 50' from the � P P PY 1. Controls shall be hand operated or automatic. space at least 27' high, 30" wide and 19" deep shall be provided. � W � � signal (measured in a horizontal plane). 1:10 Max. slo e 2. Controls shall be operable with one hand and shall not require tight grasping, rn P ANSI 602.4 - SPOUT OUTLET HEIGHT 8. No place in common corridors or haliways shall be more than 50' from the � V J Standard Curb Ramo pinching, or twisting of the wrist. ANSI 902.3- HEIGHT OF TABLES OR COUNTER � � 36" Min. A. Wheelchair accessible spout outlets shall be 36 inches mox. aff. Standing person 3. The force re uired to activate controls shall be no reater than 5 Ib. signal. s ut outlets shall be 38 inches min. & 43 inches max. aff. q 9 A. The tops of accessible tables and counters shall be 28" minimum, and 34 maximum, � � � � �p �� P� Adjoining Slope Shall P° a 48" MIN. above the finished floor. � w Not Exceed 1:20 ANSI 602.5 - SPOUT LOCATION � � � � ANSI 308 - HEIGHT (REFERENCE DETAIL 4.30.3) A. Spout shall be located 15 inches min. from the vertical support and 5 inches max. �� A. Unobstructed front approach - 48' max. to 15" min. A.F.F. Controls located in an Location of Typical Parking from the front edge of the drinking fountain, including bumpers. • '� �� i Q 703 SI(�IAGE M � alcove >24 deep must have 36" clear floor width. Access Aisle B. Unobstructed side approach - 48° max. to 15" min. A.F.F. Controls located in an � ANSI 602.6 - WATER FLOW =� =o �______ _ WHERE APPLICABLE � �� alcove >15" dee p must have 60' clear floor width. � A. Spout shall provide a flow of water 4 inches min. in height. The angle of the water � .E o A. Signs which designote permanent rooms and spaces shall comply with the C. Electrical dc communication system receptacles shall be mounted no less than 15" � Ramps (1:12 Max. Slope} stream from spouts within 3 inches of the front of the drinking fountain shall be 30 �o n requiremen ts lis te d be low for: D E P T H (R E F E R E N C E D E T A I L 4.2 5.1) 14 MIN above the floor. 1:12 Max. slope Shall Have Detectable Wamings degrees max. and from spouts between 3 inches & 5 inches from the front of the � ,�,.s 1. Raised and Braille Characters, and Pictograms A. Storage areas may be 36° in depth or less. If more than 36" in depth then area Detail 4.18.1 Detail 4.18.2 2. Fnish and Contrast and contrasting color. drinking fountain shall be 15 degrees max., meosured horizontally relative to the must allow 60° diameter of clear floor space for turning. Curb Ram Parallel to Curb Note : If Slo e is 1:20 or less no front face of the drinking fountain. Exception: Employee narne signs are not required to comply. ANSI 309 - OPERATION R contrastin coPor or texture is re uired Operable parts shall be operable with one hand and shall not require tight grasping, Detail 4•7 9 q ANSI 905.2 - CLEAR FLOOR SPACE: (REFERENCE DETAIL 4.25.2) pinching, or twisting of the wrist. The force required to activate operable parts shall be WHERE APPLICABLE 5.OIbs maximum. 5"MAX 15"MIN A. Signs which provide direction to, or information about, functional spaces of the qNSI 905.3 - HEIGHT (REFERENCE DEIAIL 4.25.3 & 4.25.4) 606 lJS1VATORIE$ building shall comply with the requirements listed below for: IBC with WA STATE AMENDMENTS 1101.2.10 - CONTROL SWITCHES ANSI 406.10 - DIAGONAL CURB RAMPS �----- --- 1. Character Proportion 308.2.1 Where a forward reach is unobstructed, the high forward reach shall be 48" A. If diagonal curb ramps have retumed curbs or other well-defined edges, such edges 2. Character Height Manually operated control switches shall comply with ANSI Section 309, except they shall � ANSI 606.3 & 606.2 - HEIGHT & CLEARANCES (REFERENCE DEfAIL 4.19.1 & 4.19.2) maximum and the low forward reach shall be 15" minimum above the floor. CQ�'ULTA� be laced 37' minimum and 40" maximum above the floor. The clear floor s ace shall be parallel to the direction of pedestrian flow. The bottom of diagonal curb � 3. Finish and Contrast P P ram s shall have 48" minimum clear s ace outside active traffic lanes of the � A. Lavatories shall be mounted with the rim or counter surface no higher than 34 Exce tion: Buildin directories, menus, and all other si ns which are ad'acent to the control switch shall be lacated be ond the arc of the door swin and P P �------ P 9 9 1 Y 9 above the finished floor. 308.2.2 Where a side reach is provided, accessible storage spaces shall be 48" centered on the control switch. roadway. If diagonal curb ramps are provided at marked crossings, the 48° clear temporary are not required to comply. space sholl be within the markings. If diagonal curb ramps have flared sides, they t. Lavatories shall extend 17" minimum from the wall. maximum and 9' minimum A.F.F. Maximum height shall be 48" for an shall also have at least a 24" long segment of straight curb located on each side 2. Clearance of 27" minimum shall be provided from the finished floor to bottom WHERE APPUCABLE (REFERENCE DEfAIL 4.30.1) unobstructed side reach and 15" minimum AFF. For side reach over an of the curb ramp and within the marked crossing. Forward roach of apron. A. Element and spaces of accessible facilities which shall be identified by the obstruction, maximum height shall be 46" and maximum depth 24", or 3. Knee clearance of 27' high minimum shall extend 8" minimum under the edge International Symbol of Accessibility are: maximum height of 34" and depth of 24'. ,� �� _ w�� ANSI 406.11 - ISLANDS of the lavatory, 30" wide minimum, and 19" deep minimum. 1. Parking spaces designated as reserved for persons with disabilities. A. Any raised islands in crossings shall be cut through level with the street or curb 4. Toe clearance of 9" minimum shall be provided for the full depth of the 2. Accessible passenger loading zones. A. Clothes rods or shelves shall be a maximum 54" above floor where a side reach is IBC 1104 - LOCATION ramps at both sides and a level area at least 48" long and 36" minimum wide � ��. � lavatory. 3. Accessible entrances when not all are accessible (inaccessible entrances shall have required. A. At least one accessible route shall be provided from public transportation stops, between the curb ramps in the part of the island intersected by the crossings. directional signage to indicate route to nearest accessible entrance). B. Where the distance from the wheelchair to the clothes rod or shelf exceeds 10" (as accessible parking and loading zones, and public streets or sidewalks to the ANSI 603.2.3 - DOORS ANSI 606 - DEPTH 4. Accessible toilet and bathing facilities when not all are accessible. at closets with inaccessible doors) the following criteria shall be met: A. Each sink shall be a maximum of 6-1/2" deep. 1. Shelves: Reach: 21" maximum; hei ht: 48" maximum, 9" minimum. accessible building entrance. A. Doors shall not swing into the clear floor space or clearance for any fixture. 9 B. Pedestrian route connections shall be clearly demarked where it crosses drive aisles. � ANSI 703.2.4 - CHARACTER HEIGHT (REFERENCE DETAIL 4.30.2) 2. Clothes rods: Reach 21" maximum; height: 48" maximum. Method of demarkation shall match existing in shopping center. painted striping. ANSI 603.2 - CLEAR FLOOR SPACE � Height: The uppecase letter "P shall be used to determine the allowable height of all 410 PLAIFORY LIF1'S A. The accessible fixtures and controls required in 4.22.7 shall be on an accessible � t characters of a font and shall be a minimum of �' and 2" maximum. ANSI 309 - HARDWARE ANSI 403.5 - WHEELCHAIR PASSAGE WIDTH route. An unobstructed turning space complying with 304 shall be provided within an w . A. Hardware for accessible storage facilities shall be operable with one hand and shall ANSI 410.1 - GENERAL � � not re uire ti ht ras in inchin or twistin of the wrist. A. The minimum clear width for single wheelchair passage shall be 32" at a point for a accessible toilet room. The clear floor space at fixtures and controls, the accessible � 17' Mi \ EXCEPTION: Where separate tactile and visual characters with the same information are q 9 9 P 9� P 9� 9 A. Platform lifts shall comply with Section 410 and ASME/ANSI A18.1 listed in Section E o B. The force re uired to activate the hardware shall be no reater than 5 Ib. max. len th of 24" and 36" continuousl , er Table 403.5 below . route, and the turning space may overlap, however; the only tuming space provided o rovided, the hei ht of the tactile u er case letter "I" shall be ermitted to be 4 9 9 Y P � ) 105.2.6. Platform lifts shall not be attendant operated and shall provide unassisted P 9 PP P � entry and exit from the lift. shall not be located within a stall. r - - minimum. '� � clear ?o�' ANSI 603.3 & 606 - LAVATORIES AND MIRRORS • o � � � floor ° ANSI 703.2.5 - CHARACTER WIDTH R�C�STERE� ' MINIMUM ANSI 410.2 - LIFf ENTRY c.� 5 s ace D . ARCHiTECT A. If lavatories and mirrors are provided, then at least one of each shall comply •-� � o � ,,� P A. Width: The u ercase letter 0" shall be used to determine the allowable width of all sECMEHr tFHcrH SEGMENT WIDTH A. Lifts with doors or gates shall comply with Section 410.2.1. Lifts with ramps shall � L _ _ PP - • with 603.3 & 606. Accessible lavatories and mirrors shall not be located within toilet �, characters of a font, and shall be 55� min. and 110� max. of the hei ht of the �ess than or 3r comply with Section 410.2.2. �, N e 9 stalls unless other accessible lavatories and mirrors are provided in the toilet room. N 19" a u ercase "P of the font. � ual to: 24 PP i greater than: 24 3G' ANSI 410.2.1 - DOORS AND GATES 8" Min Max. 48" Min. � 60� gTpZ�Q� '�� A. Doors and gates shall be low energy power operated doors or gates complying with ANSI 603.3 - MIRRORS (REFERENCE DETAIL 4.19.1) OVERHEAD SIGNS ANY AMOUNT Section 404.3. Doors shall remain open for 20 seconds minimum. End door clear A. Mirrors shall be mounted with the bottom edge of the reflecting surface 40" � � • Detail 4.19.1 Detail 4.19.2 A. Choracters and numbers on overhead signs shall be sized according ta the viewing o enin width sholl be 32 inches minimum. Side door clear o enin width shall be maximum A.F.F. Mirrors not located above lavatoreis, sinks ar counters shall be distance from which the are to be read. i IBC with WA STATE AMENDMENTS 1101.2.2 - CLEAR WIDTH P 9 P 9 y A Clear width of an accessible route shall com I with ANSI Table 403.5 above . For 42 inches minimum. mounted with the bottom edge of the reflecting surFace 35' maximum above the 1. For signs higher than 70" A.F.F., character size shall be 2" minimum plus �" per � Py � � Exc�ption: floor. foot of viewing distance above 15 feet. � � s�y � Submittals/Revisions: exterior routes of travel, the minimum clear width shall be 44". ANSI 606.6 - EXPOSED PIPES AND SURFACES Lifts serving two landings maximum and having doors or gates an opposite sides 2. The minimum height is measured using an upper case letter "1°. vl �f A. Hot cold water and drain i es under lavatories shall be insulated or otherwise 'b � / shall be permitted to have self closing manual doors or gates. � P P 3. Lower case letters are ermitted. � � ANSI 403.5.2 - PASSING SPACE configured to protect against contact. P �� FOR PERMIT 05/04/16 A. If an accessible route is less than 60" in width, then passing spaces of at least p,�Sl 410.2.2 - RAMPS B. There shall be no sharp or abrasive surfaces under lavatories. ANSI 703.3-703.5 - TACTILE, BRAILLE, & PICTOGRAMS � 60"x60" shall be provided at 200' max. spacing. A. End ramps shall be 32 inches minimum in width. Side ramps shall be 42 inches 604 INATER CLOSET'S �t TOILET COkIPARTWIENiS A. Tactile characters shall comply with sections 703.3 and shall be duplicated in braille � .�� B. The minimum clear width for two wheelchairs to pass is 60" minimum in width. ANSI 606.4 - FAUCETS ANSI 604.3 - CLEAR FLOOR SPACE A. Controls shall be operable with one hand and shall not require tight grasping, complying with section 703.4. ANSI 307.2 ANSI 410.3 - FLOOR SURFACES A. Cfear floor space for water closets not in stalls shall be provided as follows: pinching, or twisting of the wrist. B. Letter and numerals shall be raised 1/32", upper case, sans serif and s�iall be IBC 1009.2 and 1010.5.2 B. The force required to activate controls shall be no greater than 5 Ib. accompanied by grade 2 Braille. Detail 4.25.1 Detail 4.25.2 A. Floor surfaces of platform lifts shall comply with Section 302 Front approach - 48" min. wide x 66" min. long 1. Raised character hei ht: minimum to 3' lus er foot of viewin distance A. Accessible routes shall have 80" min. clear head room. C. Lever-operated, push-type, and electronically controlled mechanisms are examples of 9 � P � P 9 Side approach - 56" min. to front of toilet x 48" min. wide occe table desi ns. above 21 feet. ANSI 410.4 - PLATFORM TO RUNWAY CLEARANCE Both a roach - 60" min. wide x 56" min. lon Reference Detail 4.16 P 9 ANSI 403.3 - SLOPE PP 9 � � D. If self-closin valves are used the faucet shall remain o en for 10 seconds 2. Braille shall be contracted (grade 2); shall be located below title corresponding A. The clearance between the platform sill and the edge of any runway landing shall be B. No door swings are allowed in clear floor area. 9 P text. A. Running slope shall not exceed 1:20. 1 1/4 inch maximum minimum. B. Cross slope shall not exceed 1:48 3. Pictograms shall be accompanied by the equivalent verbal description placed ANSI 410.5 - CLEAR FLOOR SPACE ANSI 606.7 - CONTROLS AND DISPENSERS directly below the pictogram. A. Clear floor space of platform lifts shall comply with Section 305. 55' MIN. A. If controls, dispensers, receptacles, or other equipment are provided, then at least 4. The border dimension of the pictogram shall be 6" min. in height. .. .. 4 MIN. 17� HOLD one of each shall be on an accessible route and shall comply with detail 4.27 - • • ANSI 410.6 - CLEAR FLOOR SPACE (Controls & Operating Mechanisms). ANSI 703.3.12 - FINISH AND CONTRAST � A. Characters and their background shall have a nonglare finish. Characters shall �� A. Controls for platform lifts shall comply with Section 309. z ANSI 606.7 - OPERABLE PARTS contrast with their background, with either light characters on a dark background, or �,� � ANSI 404.2.1 - DOUBLE - LEAF DOORWAYS A. Operable parts on towel dispensers and hand dryers shall comply with Table 606.7 dark characters on a light background. � d- A. Doorways with two independently operated leaves shall have at least one active leaf �7O (below). � that meets the requirements in 404.2.2 and 404.2.3 ( -- ANSI 703.3.10 & 703.3.11 - MOUNTING LOCATION AND HEIGHT (REFERENCE DETAIL 4.30.3) 502/503 P/�RI(ING AND PI►SS�IGER LQADING ZONfS I ��' ` A. Characters and their background shall have a nonglare finish. Characters shall � � ANSI 404.2.2 - CLEAR WIDTH N � contrast with their background, with either light charocters on a dark background, or A. Doorwa s shall rovide a clear o enin of 37' minimum, with the door o en 9U. I D dark characters on a li ht back round. 21" MAX 1" M Sheet Title: ACCESSIBILITY GUIDELINES Y P P 9 P Maximum 0.5 2' S � 9' 11' 9 9 1. Clear opening shall be measured between the face of the door and opposite stop. ANSI 502 - PARKING SPACES I Reach Depth B. Where a tactile sign is mounted next to a door, it shall be placed to the latch side A. Accessible car parking spaces shall be 96" minimum in width. Van parking spaces o of the door wherever ossible. Where a tactile si n is laced ad'acent a double door, 2. Openings more than 24" in depth shall provide a clear opening of 36" minimum. L _ _ _ _ Maximum � .4e�- .� 4p" 3�' 34 p 9 p � Detail 4.25.3 Detail 4.25.4 shall be 132" minimum in width. Reacn Heignt � � � the sign shall be to the right hand door. If there is no wall space to the right, ANSI 404.2.3 - MANEUVERING CLEARANCES AT DOORS EXCEPTION: Van parking spaces shall be permitted to be 96" minimum in width �-� signs shall be placed on the nearest adjacent wall. Exception: Door mounted signs Provide level (1:48 max. slope) and clear maneuvering area at doors as follows: where the adjacent access aisle is 95' minimum in width. shall be permitted on the push side on the doors with closers and without hold open Date: 05/04/16 A. Front approach pull side - 60" min. width & 18" min. beside strike edge B. Parking access aisles shall be 60" wide. Van accessible access aisles shall be 96" ANSI 604.4 - HEIGHT (REFERENCE DETAIL 4.16.2) devices. Front approach push side - 48 min width & 0" beside strike edge wide. A. The height to the top of the toilet seat shall be 17' - 19" above floor. C. Tactile characters shall be 48" minimum above the floor, measured to the baseline . C. Surface slo e shall not exceed 1:48 in all directions IBC with WA STATE AMENDMENTS 1101.2.7 - OPERABLE PARTS Desi n: (12' � strike if door has both a closer and a latch) P 1. Seats shall not be sprung to return to a lifted position. of the lowest tactile character and 60" maximum above the floor, measured to the g A. Operable parts on drying equipment, towel or cleansing product dispensers and B. Hinge side approach pull side - 60° min. width; 36" min. beside strike edge or - (Note : no built up curb ramp may be located in an accessible parking access baseline of the highest tactile character. disposal fixtures shall comply with ANSI Table 606.7 (above), except the maximum 54" min. width; 47' min. beside strike edge aisle.) ANSI 604.5 - GRAB BARS (REFERENCE DETAILS 4.16, 4.16.2 & 4.16.3) D. Mounting location for such signage shall be so that a person may approach within reach height shall be 40" for reach depths less than s Drawn: Hinge side approach push side - 47' min. width & 27' min. beside hinge edge A. For water closets not located in toilet stalls, the following grab bars shall be 3" of signage without encountering protruding objects or standing within the swing of � (48"min. width if door has both a closer and a latch) provided, 33" - 36" above the finish floor: a door. a C. Lotch side approach pull side - 48" min. width and 24 min. beside strike edge 1. Side wall horizontal: 47' long minimum, hold 12° min. from back Wau. ProJect No: 15-198 a (54"min. width if door has a closer) 2. Side wall vertical: 18" high minimum, hold 39" min. from back wall. IBC with WA STATE AMENDt�ENTS 1101.2.9 - INTERNATIONAL SYMBOL OF ACCESSIBILITY N Latch side a roach ush side - 47' min. width and 24 min. beside strike ed e 3. Back wall: 36" long minimum, 17' minimum each side of water closet centerline. A. Where the Intemational Symbol of Accessibility is required, it shall be proportioned � pP p 9 Refer to 4.26 Grab Bars for size and structural elements. complying with ANSI Figure 703.6.3.1. All interior and exterior signs depicting the Approved: �� (48'min. width if door has a closer) Intemational Symbol of Accessibility shall be white on a blue background. � ANSI 404,2.4 - THRESHOLDS AT DOORWAYS ANSI 604.6 - FLUSH CONTROLS (REFERENCE DEfAIL 4.16.3) � A. Maximum threshold height: 1/2". Raised thresholds and floor level changes shall be A. Controls shall be 44" maximum above the finish floor. Bullding No: � beveled with a slope no greater than 1:2 1. Lever controls or flush valves shall be mounted on the wide and open side of � toilet areas. Except in ambulatory occessible compartments- refer to IBC, WA � State Amendments, section 1101.2.7. 2. Controls shall be hand operated or automatic. Sh22t N0: � 3. Controls shall be operable with one hand ond shall not require tight � � grasping, pinching, or twisting of the wrist. � 4. The force required to activate controls shall be no greater tna� 5�bf. COPYRIGHT CRAFT ARCHITECTS 2016