Laserfiche WebLink
I <br /> j <br /> Liebert® DS Seismic Floorstand Safety Information Floorstand Preparation: <br /> WARNING! '. 1.) Attach the mounting plates to the bottom of the floorstand with the <br /> Thermal Management Risk of unit falling over!Improper handling can cause equipment damage, hex head self drilling screws(1/4-14 X 3/4)provided.See Figure1 <br /> injury or death!Read all of the following instructions before attempting to <br /> I move,lift or remove packaging from or prepare unit for installation. for details(6 screws per plate). <br /> Reference Guide for CAUTION: <br /> Risk of contact with sharp edges,exposed fasteners and splinters!Can cause Figure 1:Mounting Plate to Floorstand <br /> Floorstand Installation injury.Only properly trained personnel wearing appropriate OSHA approved / <br /> DO NOT THROW AWAY! Personal Protection Equipment(PPE)should attempt to move,lift or remove <br /> packaging from or prepare unit and floorstand for installation. <br /> '''47 '' <br /> Equipment Inspection ��/. <br /> Upon arrival of the unit,and before unpacking,verify that the labeled equipment <br /> 1 ., matches the Bill of Lading.Carefully inspect all items for either visible or concealed damage.Damage should be immediately reported to the carrier and a <br /> damage claim filed with a copy sent to Liebert Corporation or to your sales <br /> YA representative. <br /> 1(4-14ill <br /> 314Self-D "Material ln IwOUntln Plate <br /> g9lik.4* Packing <br /> � Screw <br /> n y All material used to package this unit is recyclable.Please save for (1261:4 <br /> 6 per ate L j <br /> 1S4 <br /> future use or dispose of the material appropriately. <br /> Front <br /> O' ..r 'fly <br /> Purpose: <br /> This reference guide provides information for installing a Liebert DS 2.) Repeat for remaining plates.For floorstands 85in(2159mm)in <br /> seismic floorstand.The assembled floorstand design is certified to meet length and less,the quantity will be four.For floorstands longer <br /> the seismic requirements of UBC 1997/2001,Zones 1 through 4.If your than 85in(2159mm),the quantity will be six. <br /> This floorstand meets the seismic requirements of UBC 1997/2001, application requires other seismic requirements and/or standards,please 3.) Install the leveling feet with orientation as shown in Figure 2. <br /> Zones 1 through 4 and intended for use with Liebert®DS products. contact your local Liebert representative. <br /> Figure 2:Leveling Feet Orientation(top view) <br /> Location: ti / a` <br /> N. <br /> j The floorstand is shipped separately from the Liebert Environmental <br /> I conditioning unit/cooling system equipment. <br /> Itemized Contents: Leveling Foot <br /> Mounting Plate <br /> Floorstand—Consult unit installation specification sheet for height /� <br /> ordered. �a?Z _.?'�cf <br /> Turning Vane(optional) Typical floorstand shown for clarity,actual design may vary. <br /> Q VERTIV. Seismic Mount Adjustable Leveler Feet <br /> Hardware <br /> Mounting Plate&Leveling Foot <br /> Quantity is 4 for units s 85in(2159mm)long <br /> Quantity is 6 for units>85in(2159mm)long <br /> Attachment Plates—See Figure 5 <br /> 1/4-14 X 3/4 Self-Drilling Hex-Head Screws <br /> Installation Instructions <br /> NOTICE: <br /> This assembled seismic floorstand is a seismically certified design.Changes or <br /> deviations from the design and/or these assembly instructions will void the <br /> 182284P1 Rev4 <br /> certification! <br />