Laserfiche WebLink
lI f <br /> . <br /> d <br /> ' <br /> 4.) To adjust the vertical height of the leveli n g feet,adjust and tighten 7.) Determine the location for the attachment plates.The plates are <br /> the nuts and jam nut as shown in Figure3.The seismic floorstand required to be under the compressor section of the unit and also <br /> must be level and all feet must be in co tact withithe floor before below each panel of the unit.Thejplates need to be located i it <br /> proceeding. ! I between the panel lances.See Figures 4&Chart 2 for details. <br /> Figure 3:Leveling Feet Heig t Adjustment <br /> Top ISO View I III Bottom ISO View Figure 4:Attachment Plate Location(Front View) <br /> 5 r AFI I Locate plate Locate plate <br /> �! o� between between <br /> /►� panel lances panel lances I <br /> liar�r�lI <br /> - <br /> IIII <br /> ,� Flush Fit �- I <br /> .ur G, , . ‘ <br /> c / <br /> fall plates} \ pp. <br /> I ..1 II <br /> Top Adjusting Nut Bottom Jam Nut <br /> Adjusting Nut Attachment plates <br /> Ill located below Attachment plates — <br /> 5.) Floorstand Anchorage.Secure levelingfeet to substructure compressor section located below each panel Technical Support <br /> g (required in front and rear) <br /> (required in front and rear) United States1 i Europe <br /> (concrete floor).Mounting requirement details such as anchor p <br /> brand,type,embedment depth,edge spacing,anchor-to-anchor 1050 Dearborn Drive Via Leonardo Da Vinci 8 <br /> Chart 2:Attachment Plate P.O.Box 29186 <br /> spacing,concrete strength,(special inspection anis attachment to Zona Industriale Tognana <br /> Floorstand Attachment Plate Quantity Columbus,OH 43229 35028 Piove Di Sacco(PD)Italy <br /> non-building structures must be outlinedl'and approved by the Length Front or Rear Unit Vertiv Services: +39 049 9719 111 <br /> Engineer of Record for the project or building.Structural floors and <br /> !I (inches) I Side Total 24.7 dispatch of technicians- +39 049 5841 257:FAX <br /> housekeeping pads must also be seismically designed and 72 3 6 all products 1-800-543-2378 <br /> approved by the project or building Structural Engineer of Record 85 3 6 Asia <br /> to withstand the seismic anchor loads.The installing contractor is 97 4 8 Technical Support 8x5 M-F 23F,Allied Kajima Bldg. <br /> responsible for the proper installation()fell anchors and mounting 138 Gloucester Road <br /> hardware,observing the mounting requirements'detailed in the 108 4 8 Thermal Managment VVanchai <br /> seismic installation drawings and additionally outlined by the 131 5 10 1-800-543-2788 Hong Kong <br /> Engineer of Record.The maximum load llat the anchor is provided Channel Products +852 2 572 2201 <br /> for proper sizing of the anchors based on unit length in Chart 1. 8.) Secure the Liebert DS to the seismic floorstand using the 1-800-222-5877 , +852 2 831 0114 FAX <br /> attachment plates and fasteners provided.The bottom of the plate AC/DC Power <br /> Chart 1i:Anchor Loads should be flush with the bottom edge of the top seismic floorstand 1-800-543-2378 ' <br /> I Maximum Load per Anchor <br /> horizontal member(see Figure 6).Use four 1/4-14 X 3/4 self- <br /> Unit Length Unit Mass drilling screws(provided)per attachment plate(refer to Figure 5). Web Site <br /> I Tension Shear www.VertivCo.com <br /> inches mm Lbs kg Lbs'h, kg Lbs kg The top two holes of the plate must be fastened in the bottom <br /> frame of the Liebert DS and the bottom two holes of the plate will <br /> 72 1829 2040 761.4 845.011 315.4 208.0 77,6 be fastened into the seismic floorstand structural member. While every precaution has been taken to ensure the accuracy and <br /> 85 2159 2354 878.6 949.011 354.2 240.0 89.6 completeness of this literature,Vertiv Co assumes no responsibility <br /> 97 2464 2342 874.1 333.011 124.3 99.0 37.0 Figure 5:Secure Liebert DS to Seismic Floorstand and disclaims all liability for damages resulting from use of this <br /> 108 2743 3074 1147.3 426.01' 159.0 130.0 48.5 1 information or for any errors or omissions. <br /> 131 3327 4008 1496.0 536.011 200.1 170.0 63.5 1/4-14 X 3/4 Self-Drilling Screws 1 <br /> (4 per attachment plate) Liebert DS ©2017 Vertiv Co <br /> 6.) Consult unit installation manual(SL-188• <br /> 25)priorto setting unit on All rights reserved throughout'the world. Specifications subject to <br /> Floorstand. — change without notice. All names referred to are trademarks dr <br /> illNoinem <br /> registered trademarks of their,respective owners. <br /> ems <br /> ®Liebert is a registered trademark of Vertiv Co. I, <br /> Seismic <br /> Attachment The Vertiv logo is a trademark and service mark of Vertiv Co. <br /> 1Plate Floorstand <br /> Flush on 182284P1_Rev.4 <br /> This Edge <br /> Printed in USA <br /> 9/ ti <br /> I <br /> 1 <br />