Laserfiche WebLink
I <br /> I1 9-08.1(2)G be used as a first coat. In both cases the first may coat shall be <br /> 2 compatible with galvanizing and as recommended by the top coat manufacturer. <br /> 13 <br /> 4 2. The second coat shall be a top coat moisture cured aliphatic polyurethane <br /> 5 conforming to Section 9-08.1(2)H or a top coat polyurethane conforming to <br /> I 6 Section 6-07.3(10)H Option 2 NEPCOAT performance based paint specification <br /> 7 compatible with the first coat as recommended by the manufacturer. <br /> 8 <br /> 9 Each coat shall be dry before the next coat is applied. All coats applied in the shop shall be <br /> I 10 dried hard before shipment. <br /> 11 <br /> 12 6-07.3(11)B Powder Coating of Galvanized Surfaces <br /> I 13 This section is revised to read: <br /> 14 <br /> 15 Powder coating of galvanized surfaces shall consist of the following coats: <br /> I 16 <br /> 17 1. The first coat shall be an epoxy powder primer coat conforming to Section 9-08.2. <br /> 18 <br /> I 19 <br /> 20 2. The second coat shall be a polyester finish coat conforming to Section 9-08.2. <br /> 21 6-07.3(11)B3 Galvanized Surface Cleaning and Preparation <br /> 22 The first three paragraphs are revised to read: <br /> I 23 <br /> 24 Galvanized surfaces receiving the powder coating shall be cleaned and prepared for <br /> 25 coating in accordance with ASTM D 7803, and the project-specific powder coating plan. <br /> 1 26 <br /> 27 Assemblies conforming to the ASTM D 7803 definition for newly galvanized steel shall <br /> 28 receive surface smoothing and surface cleaning in accordance with ASTM D 7803, Section <br /> I 29 5, and surface preparation in accordance with ASTM D 7803, Section 5.1.3. <br /> 30 <br /> 31 Assemblies conforming to the ASTM D 7803 definition for partially weathered galvanized <br /> 32 steel shall be checked and prepared in accordance with ASTM D 7803, Section 6, before <br /> I 33 then receiving surface smoothing and surface cleaning in accordance with ASTM D 7803, <br /> 34 Section 5, and surface preparation in accordance with ASTM D 7803, Section 5.1.3. <br /> 35 <br /> I 36 The fourth paragraph (up until the colon) is revised to read: <br /> 37 <br /> 38 Assemblies conforming to the ASTM D 7803 definition for weathered galvanized steel shall <br /> I 39 be prepared in accordance with ASTM D 7803, Section 7 before then receiving surface <br /> 40 smoothing and surface cleaning in accordance with ASTM D 7803, Section 5, and surface <br /> 41 preparation in accordance with ASTM D 7803, Section 5.3 except as follows: <br /> 42 <br /> I43 6-07.3(11)B5 Testing <br /> 44 Item number 4 in the first paragraph is revised to read: <br /> 45 <br /> I 46 4. Adhesion testing in accordance with ASTM D 4541 for 600 psi minimum adhesion for <br /> 47 the complete two-component system. <br /> 48 <br /> I 49 The second sentence of the fourth paragraph is revised to read: <br /> 50 <br /> I City of EverettPage AM 55 Amendments <br /> Everett Station 80 Stall Parking Expansion June 2019 <br /> I <br />