1920 100TH ST SE 2021-12-13 - Laserfiche WebLink

Adk 01101116 Lighting, Motor,and Libctrical Permit Checklist, ' 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2, R3, R4 over 3 stories and all R1 Revised July 2016 Project Title: SEA MAR EVERETT MEDICAL CLINIC Date 6/18/2019 The following information is necessary to check a permit application for compliance with the lighting, motor, and electrical requirements in the Washington State Energy Code, Commercial Provisions. Applicability ILocation in Building Department (yes,no, na) I Code Section Component Compliance information required in permit documents Documents Notes LIGHTING CONTROLS YES C405.2 Lighting controls, For all lighting fixtures, indicate lighting control method on plans A2.03 general for spaces and lighting zone(s) served, or exception taken Luminaire level Indicate on plans all fixtures provided with LLLC in lieu of YES C405.2 lighting controls - C405.2 lighting controls; provide description of control A2.03 (LLLC) capabilities and performance parameters For permanently installed lighting fixtures in dwelling units, NA C405.1 Lighting in dwelling indicate lighting control method on plans for spaces and units lighting zone(s) served, or demonstrate compliance with high efficacy exception C405.2.3 Indicate on plans the method of manual lighting control (whether C405.2.1.1 combined with occupancy sensor, automatic light reduction, YES C405.2.2.2 Manual controls daylight responsive or specific application controls), location of A2.03 C405.2.4 manual control device and area or specifice application it C405.2.5 serves C405.2.2.1 Manual interior Indicate on plans which method of manual 50% lighting load YES C405.2.2.2 lighting controls reduction is provided, or whether lighting load is reduced via A2.03 C405.2.3 occupancy sensors or daylight responsive controls Indicate on plans the method of automatic shut-off control during unoccupied periods (occupancy sensor or time switch) A2.03 Method of automatic for all lighting zones; YES C405.2.2 shut-off control Indicate locations where automatic shutoff is provided by other methods (occupancy sensor or digital timer switch) or which time switch control exception applies Indicate on plans the spaces served by occupancy sensors; Indicate whether occupancy sensor controls are configured to YES C405.2.1 Occupancy sensor C405.2.1.1 controls be manual -on, automatic 50%-on, or serve a space eligible for A2.03 automatic 100%-on per exception Occupancy sensor Indicate aisleways and open areas in warehouse spaces NA C405.2.1.2 controls - provided with occupancy sensor controls that reduce lighting warehouses power by 50% YES C405.2.6 Digital timer switch Indicate required digital timer switch control function when A2.03 control is used YES C405.2.2.1 Automatic time Indicate locations of override switches on plans and the lighting A2.03 switch controls zone(s) served, include area sq. ft. Indicate primary and secondary sidelight daylight zone areas on A2.03 plans, include sq. ft.; Indicate toplight daylight zone areas on plans, include sq. ft._ AE2.01 C405.2.4.2 Daylight zones - For small vertical fenestration assemblies (rough opening less YES C405.2.4.3 Sidelight and toplight than 10 percent of primary daylight zone) where daylight responsive controls are not required, provide fenestration area to daylight zone calculation(s) Indicate on plans lighting zone(s) served by daylight responsive A2.03 controls; Identify sidelight and toplight daylight zones that are not provided with daylight sensing controls and the exception(s) that AE2.01 YES C405.2.4 Daylight responsive apply; Indicate on plans the lighting load reduction method - controls continuous dimming, or stepped dimming that provides at least two even steps between 0%-100% of rated power; Indicate that daylight sensing controls are configured to completely shut off all controlled lights in the lighting zone Additional controls - Identify spaces and lighting fixtures on plans that require YES C405.2.5 Specific application specific application lighting controls per this section AE2.01 lighting controls Indicate on plans that display and accent lighting, and display C405.2.5 - Display and accent case lighting are controlled independently from both general A2.03 YES Items 1&2 lighting area lighting and other lighting applications within the same space; Indicate manual and automatic lighting control method