1410 SEINER DR 2024-04-12 - Laserfiche WebLink

• Powered directly by two-wire SLC loop. No additional Wire length:6"(15.24 cm)minimum. power required. • High noise(EMF/RFI)immunity. NZM-100(A) Interface Module • Tinned,stripped leads for ease of wiring. • Supports compatible two-wire smoke detectors. • Direct-dial entry of address:01-99 on FireWarden-100-2, • Supervises IDC wiring and connection of external power 01 -50 on FireWarden-50. source. — --- - • High noise(EMF/RFI)immunity. Ett 3 1415 0 1 ADDRESS o 1 • SEMS screws with clamping plates for ease of wiring. f 1311 2 2 • Direct-dial entry entry of address:,01-99 on FireWarden- 3 �///P 4 LOOP �� 4 100-2,01 -50 on FireWarden-50. 10 5 5 • LED flashes during normal operation. 9 8 7 6 9 g 7 6 • LED latches steady to indicate alarm on command from TENS ONES control panel. The NZM-100(A) Interface Module is intended for use in intelligent, addressable systems, where the individual address of each module is selected using built-in rotary O W Q U switches. This module allows intelligent panels to interface J JO W Q and monitor two-wire conventional smoke detectors. It trans- Lu-1 mits the status (normal, open, or alarm) of one full zone of conventional detectors back to the control panel.All two-wire detectors being monitored must be UL compatible with the module. ,J NZM-100(A) APPLICATIONS The NMM-100P(A)Mini Monitor Module can be installed in a Use the NZM-100(A) to monitor a zone of two-wire smoke single-gang junction directly behind the monitored unit. Its detectors. The monitored circuit may be wired as an NFPA small size and light weight allow it to be installed without rigid Style B (Class B) or Style D (Class A) Initiating Device Cir- mounting. The NMM-100P(A) is intended for use in intelli- cuit.A 3.9 K Ohm End-of-Line Resistor(provided)terminates gent, two-wire systems where the individual address of each the end of the Style B or D (class B or A)circuit (maximum module is selected using rotary switches. It provides a two- IDC loop resistance is 25 Ohms). Install ELR across termi- wire initiating device circuit for normally-open-contact fire nals 8 and 9 for Style D application. alarm and security devices. NMM-100P(A) NZM-100(A)OPERATION NMM-100P(A)APPLICATIONS Each NZM-100(A) uses one of the available module Use to monitor a single device or a zone of four-wire smoke addresses on an SLC loop. It responds to regular polls from detectors, manual fire alarm pull stations,waterflow devices, the control panel and reports its type and the status (open/ or other normally-open dry-contact devices. May also be normal/short)of its Initiating Device Circuit(IDC).A flashing used to monitor normally-open supervisory devices with spe- LED indicates that the module is in communication with the cial supervisory indication at the control panel. Monitored cir- control panel. The LED latches steady on alarm (subject to cuit/device is wired as an NFPA Style B (Class B) Initiating current limitations on the loop). Device Circuit. A 47K Ohm End-of-Line Resistor (provided) terminates the circuit. NZM-100(A)SPECIFICATIONS NMM-100P(A) OPERATION Nominal operating voltage: 15 to 32 VDC. Each NMM-100P(A) uses one of the available module Maximum current draw:5.1 mA(LED on). addresses on an SLC loop. It responds to regular polls from Maximum IDC wiring resistance:25 Ohms. the control panel and reports its type and the status (open/ normal/short)of its Initiating Device Circuit(IDC). Average operating current: 270 pA, 1 communication and 1 LED flash every 5 seconds,3.9k eol. NMM-100P(A)SPECIFICATIONS EOL resistance:3.9K Ohms. Nominal operating voltage: 15 to 32 VDC. External supply voltage (between Terminals T10 and Average operating current: 350 pA, 1 communication T11): every 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Shorted). • DC voltage:24 volts power limited. • Maximum IDC wiring resistance: 1500 Ohms. Ripple voltage:0.1 Vrms maximum. • Current:90 mA per module maximum. Maximum IDC Voltage: 11 Volts. Temperature range:32°F to 120°F(0°C to 49°C). Maximum IDC Current:450 pA. Humidity range: 10%to 93%noncondensing. EOL resistance:47K Ohms. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x Temperature range: 32°F to 120°F(0°C to 49°C). 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm)square x Humidity range: 10%to 93%noncondensing. 2.125"(5.398 cm)deep box. Dimensions: 1.3"(3.302 cm)high x 2.75"(6.985 cm)wide x 0.65"(1.651 cm)deep. Page 2 of 4—DN-6999:E•07/30/2015