3003 W CASINO RD BLDG 40-92 2024-06-12

INSTALLATION AND MAINTENANCE INSTRUCTIONS SY'STEM Innov hex SE NSOR C) D4120 Duct Smoke Detector D4S Sensor Component 3825 Ohio Avenue,St.Charles,Illinois 60174 1-800-SENSOR2,FAX:630-377-6495 D4P120 Power Board Component www.systemsensor.com NOTE:The D4120 duct detector consists of D4P120 Power Board component and the D4S Sensor component. SPECIFICATIONS Operating Temperature: D4120&D4S: -4° to 158° F (-20° to 70° C) D4P120: -40° to 158° F (-40° to 70° C) Storage Temperature: D4120&D4S: -22° to 158° F (-30° to 70° C) D4P120: -40° to 158° F (-40° to 70° C) Humidity: 0% to 95% Relative Humidity Non-condensing Air Velocity: 100 to 4000 ft./min. (0.5 to 20.3 m/sec.) D4120 Footprint Dimensions: Rectangular- 14.38 in L x 5 in W x 2.5 in D (37cm L x 12.7cm W x 6.36cm D) Square-7.75 in L x 9 in W x 2.5 in D (19.7cm L x 22.9cm W x 6.35cm D) D4S/D4P120 Footprint Dimensions: 7.75 in L x 5 in W x 2.5 in D (19.7cm L x 12.7cm W x 6.35cm D) D4120 Weight: 2.5 pounds; 1.14 kg Electrical Power supply voltage: 20-29 VDC 24 VAC 50-60-Hz 120 VAC 50-60 Hz Input capacitance: 270 pF max. 270 pF max. N/A Reset Voltage: 3.0 VDC min. 2.0 VAC min. 10 VAC min. Reset Time (with RTS451/RTS151): .03 to 0.3 sec. .03 to 0.3 sec. .03 to 0.3 sec. Reset Time (by power down): 0.6 sec. max. 0.6 sec. max. 0.6 sec.max. Power Up Time: 35 sec. max. 35 sec.max. 35 sec. max. Alarm response time: 15 sec. 15 sec. 15 sec. Sensitivity Test: See detector label See detector label See detector label Current Requirements (Using No Accessories) Max. standby current 21 mA @ 24 VDC 65 mA RMS @ 24VAC 60Hz 20 mA RMS @ 120 VAC 60 Hz Max. alarm current 65 mA @ 24 VDC 135 mA RMS @ 24 VAC 60 Hz 35 mA RMS @ 120 VAC 60 Hz CONTACT RATINGS ACCESSORY CURRENT LOADS AT 24 VDC Alarm initiation contacts(SPST) 2.OA @ 30 VDC(resistive) DEVICE STANDBY TROUBLE ALARM Alarm auxiliary contatcs(DPDT) 10A @30 VDC(resistive) APA151/APA451 12.5mA n/a 30mA Max. 1 OA 03250 VAC(resistive) MHR/MHW OmA n/a 29mA Max. 1/2 HP @240 VAC RA40OZIRAlOOZ OmA n/a 12mA Max. RTS451/RTS151 OmA n/a 12mA Max. 1/4 HP @ 120 VAC RTS451KEY/RTS151KEY 12mA n/a 12mA Max. NOTE:Alarm auxiliary contacts shall not be connected to initiating circuits of RTS2 3mA Max. 16mA Max. 30mA Max. control panels.Use the alarm initiation contact for this purpose. RTS2-AOS 3mA 16mA Max. 55mA Max. Supervisory Contacts(SPDT) 2.0A @ 30 VDC(resistive) NOTE:Any combination of accessories may be used such that the given accessory 2.0A @ 125 VAC(resistive) loads are:110mA or less at the Aux output,and 50mA or less at the Alarm output. TABLE OF CONTENTS PAGE IMPORTANT:This detector must be tested and maintained regularly following [1] Limitations of Duct Smoke Detectors.. . . .. . . .. . . .. . . . . . . . . . . . . 1 NFPA 72 requirements.The detector must be tested an maintained regularly fol- [2] Exploded View of Duct Smoke Detector Components . . . . . . . . . . . ..2 lowing NFPA 72 requirements. According to NFPA,the detector should be visu- [3] General Description .. . . .. . . .. . . .. . . .. . . .. . . .. . . . . . . .. . . ..2 ally inspected semiannually and functionally tested at least once a year. This [4] Contents of Duct Smoke Detector Kit.. . . .. . . .. . . .. . . . . . . . . . . ..2 may need to be more frequent depending on the air quality of the duct supply air. [5] Detector Installation.. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . ..2 [i]LIMITATIONS OF DUCT SMOKE DETECTORS [6] Sampling Tube Installation. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . ..3 [7] Measurement Tests. . . . . . . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . ..3 AWARNING [8] Field Wiring Installation Guidelines. .. . . .. . . . . . . .. . . .. . . .. . . ..4 The National Fire Protection Association has established that DUCT DETEC- [9] Unit Configuration. .. . . .. . . .. . . . . . . . . . . . . . . .. . . . . . . . . . . ..5 TORS MUST NOT BE USED AS A SUBSTITUTE FOR OPEN AREA DETECTOR [10] Detector Status Indication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 PROTECTION as a means of providing life safety.Nor are they a substitute for [11] Interconnection(Multiple Fan Shut Down). . . . . . . . . . . . . . . . . . . ..6 early warning in a building's regular fire detection system. [12] Verification of Operation.. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . ..6 System Sensor supports this position and strongly recommends that the user [13] Detector Cleaning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 read NFPA Standards 90A,72,and 101.The D4120 Air Duct Smoke Detectors [14] Sensor replacement.. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . ... . .. .7 are listed per UL 268A. [15] Optional Accessories. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . .. .7 This device will not operate without electrical power. Fire situations may Wiring Diagrams. .. . . . . . . .. . . .. . . .. . . . . . . . . . . . . . . . . . . . . . . .5-7 cause an interruption of power. The system safeguards should be discussed Warranty. . . . . . . . . . . . . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . ... . .. 8 with your local fire protection specialist. BEFORE INSTALLING Read System Sensor's Applications Guide for Duct Smoke Detectors This device will not sense smoke unless the ventilation system is operating and the cover is installed. (HVAG53), which provides information on detector spacing, placement, zoning, wiring, and special applications. This manual is available online at For this detector to function properly,it MUST be installed according to the in- www.systemsensor.com. NFPA Standards 72 and 90A should also be refer- structions in this manual.Furthermore,the detector MUST be operated within enced for detailed information. ALL electrical and environmental specifications listed in this manual.Failure to comply with these requirements may prevent the detector from activating NOTICE:This manual shall be left with the owner/user of this equipment. when smoke is present in the air duct. 1 I56-2967-008R 06-10