1509 CALIFORNIA ST DAWSON PLACE 2025-04-07

Operable K II MODEL . , . PRODUCTSPECIFICATIONS 2.01 ACCEPTABLE MANUFACTURER 2.05 FINISHES A.Operable walls shall be Series 3000,Model 3030/303oGL Hinged A.Finish Material Type:Panel finish material shall be Class A Pairs as manufactured by KWIK-WALL Company. (except wood veneer)rated in accordance with ASTM E 84, 2.02 PANEL CONSTRUCTION consisting of(select): A.Panel Dimensions:Standard panel dimension shall be a nominal 1.Vinyl:consisting of Type II,reinforced vinyl weighing 4"[lol.6]thick. 21 oz./lin.yd.(651 g/lin.m).Vinyl shall meet or exceed B.Panel Frame:Steel frame shall be 16-gauge galvanneal steel, CCC-W-4o8A and CFFA-W-ioi-D quality standards. which meets or exceeds ASTM A 653 requirements.Frame shall 2.Optional Upgrade Fabric:consisting of fade and tear be all-welded construction with steel corner supports and resistant fabric that resists water-based stains weighing cross bracing reinforcement.Panel frame shall be Class A rated, 13 oz./lin.yd.(403 g/lin.m). fire retardant, non-combustible and non-corrosive in accordance 4.Optional Basics Carpet:consisting of acoustically with ASTM E 84• absorbent,non-woven needle punch fibers fused to prevent C.Panel Skins:Panel skins shall be Class A rated in accordance with fraying and unraveling of material weighing 28.5 oz./lin.yd. ASTM E 84.Panel skin material shall consist of(select): (884 g/lin.m).Basics Carpet shall achieve a minimum NRC 1.Standard Steel Skins:consisting of minimum 22-gauge tension rating of.20(applied over gypsum substrate) accordance with ASTM C 423. leveled galvanneal steel,pressure laminated to a structural acoustical backer and mechanically fastened to the steel frame 5.Optional Upgrade Carpet:consisting of acoustically to form a rigid,unitized and structural panel. absorbent,non-woven needle punch fibers fused to prevent 2.Optional Acoustical Substrate:consisting of structural fraying and unraveling of material weighing 20 oz./lin yd acoustical substrate pressure laminated to both sides of the (713 g/lin m)Upgrade carpet shall achieve a minimum NRC steel frame to form a rigid,unitized and structural panel. rating of.25(applied over gypsum substrate)in accordance with ASTM. 3.Optional Wood Veneer:consisting of particle board core covered 6.Optional High Pressure Laminate:consisting of gypsum with wood veneer and pressure laminated to both sides of the board core covered with general purpose plastic laminate steel frame to form a rigid,unitized and structural panel. and Phenolic backer sheet,which is pressure laminated to 4.Optional High Pressure Laminate:consisting of gypsum both sides of the steel frame to form a rigid,unitized and structural panel. board core covered with general purpose plastic laminate and Phenolic backer sheet,which is pressure laminated to 7.Optional Wood Veneer:consisting of unfinished flat cut both sides of the steel frame to form a rigid,unitized and wood veneer laminated to 1/2"[12.7]thick particle board structural panel. core.Veneer shall be book/running matched within a panel,and vertically edge banded if trimless astragals are D. Optional Glass Insert(303oGL): Opening cut out in panel shall specified. be glazed with insulated glass that is manufactured in accordance with ASTM E 219o.Glass type shall be an acoustical insulated Notes:Optional Class"A"rated particle board is available. Acoustical glass unit 13/4"[44.5]thick with 1"[25.4]air space Glass substrate STC ratings apply for Wood Veneer panel construction..) shall be retained in opening cut out using an aluminum extrusion. 8.Optional Unfinished:consisting of panels with exposed E.Panel Hinges:Panel hinges shall be(select) acoustical substrate or steel skins for field applied i.Architectural grade,full leaf butt hinges. wall covering or painting. 2.Concealed hinges B.Finish Material Supplier:Finish material shall be(select): F.Panel Weight:Maximum panel weight shall be 1.Standard Factory Supplied:from manufacturer's standard 5.9-12.91bs./ft.2(29-63 kg/m2)depending on STC rating, selection of finish materials,as specified. size and options selected. 2.03 OPERATION 2.Optional Customer Supplied:from customer's selection of finish material,by others,and as approved by A.Operation shall be Hinged Pairs,consisting of panels hinged KWIK-WALL Company. together in groups of two(2),unless otherwise specified.Panels shall be top-supported by one(1)carrier in each panel. C.Finish Material Application:Finish material shall be(select): 2.04 STACK ARRANGEMENTS 1.Standard Factory Applied:by operable wall manufacturer. Customer supplied finish material samples must be A.Stack Type:Panel storage configuration shall be submitted to manufacturer for testing and approval prior to Center Stack,consisting of panels stacked on center to the acceptance and application. wall's installed position. B.Stack Quantity:Panels shall be stored at(select): 2.Optional Field Applied:by others. 1.Standard One End:on one end of the wall run. 2.Optional Both Ends:on both ends of the wall run. Dimensions in[]are millimeters.contact your local distributor for additional assistance or visit www.kwik-wall.com 04-23