Laserfiche WebLink
L City of Everett Permit Services <br /> EVERETT Reviewed for Permit 03/05/2025 <br /> ._...-°`° LEGEND <br /> SEE SHEET 40-009—M1 <br /> (E) ROOF EXHAUST FAN (E) ROOF EXHAUST FAN <br /> GENERAL NOTES <br /> 1. PH ANALYZER REQUIREMENTS SHALL BE IN ACCORDANCE <br /> ` WITH SECTION 40 75 00. <br /> i 2. FLOW METER REQUIREMENTS SHALL BE IN ACCORDANCE <br /> WITH SECTION 40 71 00. <br /> 3. PIPE SUPPORT REQUIREMENTS SHALL BE IN ACCORDANCE <br /> WITH SECTION 40 05 08. <br /> I I <br /> 4. FOR SUMP PUMP SEE DRAWINGS 40-009—M501, <br /> 40-009—OM110 AND 40-009—M311. <br /> (E) BUILDING <br /> (E) LOUVER (E) LOUVER 2 <br /> I I <br /> REFERENCE DRAWINGS <br /> A 1. HAZARDOUS LOCATION CLASSIFICATION: UNCLASSIFIED AREA. <br /> SEE DRAWING 40-009—A3. <br /> CONSTRUCTION NOTES <br /> a � INSTALL PIPE SUPPORTS PER DETAIL 3/M503. <br /> A � INSTALL PIPE SUPPORTS PER DETAIL 4/M503. <br /> WELD A 3—INCH STAINLESS STEEL THREAD—O—LET ON 10" <br /> 8 PIPE INVERT TO ALLOW INSTALLATION OF A 3—INCH NPT <br /> STAINLESS STEEL BALL VALVE. <br /> 5 10" KNIFE GATE VALVE (TYP) 5 <br /> PH METER TRANSMITTER 27"x10" FRP (E) 27" ® THE 27—INCH X 10—INCH FRP FLUME TRANSITION FITTING <br /> (E) 27" CONC PIPE FLANGES SHALL MEET ASME B16.5 REQUIREMENTS. THE <br /> CONIC PIPE FLOW METER TRANSMITTER REDUCER (TYP) 27—INCH FLANGE SHALL MATCH THE EXISTING BOLT <br /> <° Q PATTERN. <br /> 6 <br /> © 4 E� INSTALL STAINLESS STEEL ANGLE SUPPORT UNDER <br /> PH PHOBE (TYP)Q7 STAINLESS STEEL COVER PLATE. INSTALL NEOPRENE GASKET <br /> _ (CUT—TO—LENGTH) BETWEEN ANGLE SUPPORT, CONCRETE <br /> — 4 �10" FICA 10" FLOW METER — WALL, AND STAINLESS STEEL COVER PLATE TO SEAL THE (E) <br /> 10"—SAN—SS OPEN CHANNEL BYPASS. <br /> a: © INSTALL NEW 1/4" 304 STAINLESS STEEL SHUTOFF BLINDS <br /> a. WITH <br /> � RUBBER GASKET ON ONE SIDE OF THE PLATE TO <br /> +" INV EL 366.34' SEAL THE 27—INCH FLUME OPENING. <br /> U <br /> INV EL 366.05' ° aa9'° z 1 3 I 2 FF EL 363.56 <br /> 1 1 a pH PROBE PER DETAIL 1/M503 AND 2/M503. THE PRIMARY <br /> i <br /> `V AND SECONDARY pH PROBE TAP TO BE LOCATED <br /> a APPROXIMATELY 3'-8" AND 4'-11" FROM FACE OF FLANGE <br /> FROM OUTLET SIDE OF THE FLOW METER. <br /> a: <br /> 3" DRAIN ® INSTALL 2—INCH SCH 80 CPVC BULKHEAD FITTING. <br /> PIPE SUPPORT TYP OF 3 � INSTALL 2—INCH EDPM FLEXIBLE COUPLING AND SCH 80 <br /> ( ) CPVC CHECK VALVE AND BALL VALVE DOWNSTREAM OF THE <br /> P-1 <br /> SUMP PUMP. <br /> SECTION A <br /> SCALE: 1/2" = 1'-0" OM110 M502 <br /> 90% REVIEW Kennedy/Jenks Consultants <br /> 0/1" A �1 "/1 32001 32nd Avenue South,Suite 101 <br /> L �I -I L Federal Way,WA 98007 <br /> Ph.253-835-6400 <br /> Fax 253.952.3435 <br /> SYM REM" BY APPROVED DATE SYM REVISION BY APPROVED DATE ERIC ACCEPTABILITY B. HOPPER 02.11.25 DRAWN DATE SUBTITLE CURRENr REVISION SYMBOL DATE <br /> ORIG 100%FINAL DESIGN—ISSUED FOR CONSTRUCTION C238185 KJ JEA 09.25.23 �Q�`� A�0�� THIS DESIGN AND/OR B.G. DOCKTOR 02.11.25 PIPING SECTIONS AND DETAILS <br /> A SEWER METER BYPASS(PHASE 1) C238185 KJ JEA 02.11.25 SPECIFICATION IS APPROVED SHEEP <br /> BOE/Miff 2 APPROVED BY DEFT <br /> C238185 A 12.13.24 <br /> � z ' DATE J.ANDERSON 02.11.25 � M 502 <br /> CHECKED <br /> M.SPAUR 02.11.25 BUILDING 40-09 JOB NO. COMP NO. <br /> 55 3 APPROVED C238185 <br /> ONAt APPROVED MECHANICAL MASTER COL. X—X/X—X EVERETT. WA DWG No. 40-009—M502 <br />