2702 COLBY AVE PEOPLES BANK 2021-04-20

■ • � • • 2012 Washington State Energy Code Compliance Forms for Commercial.Group R1,and>3 story R2 and R3 Revised�une zoi 3 Project Address People's Bank Date 5/22/2015 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. NOTE:Define print area in Excel prior to printin MECH-CHK pages. Applicability Code Section Code Provision Information Required Location Building Department (yes,no,na) on Plans Notes GENERAL PROVISIONS,CONTINUED HVAC System Controls&Criteria,Continued C403.2.12 Variable flow control- Indicate fan&pump motors requiring VF control&method(VSD or equiv N/A fans/ um s controls C403.2.12.1 Varia6le flow control- Indicate cooling tower fans requiring variable flow control and method N/A coolin towers C403.2.12.2 Large volume fan systems Indicate fan systems requiring airflow reduction based on heating and N/A coolin demand;or exce tion taken C403.2.12.2 Single zone AC systems Indicate method of cooling demand-based fan control for sys.>110,000 N/A btuh N/A C403.2.4.10 DDC system capabilities Identify all DDC system inpuVoutput control points and indicate capabiliry fo t e e o nt t Ducting Systems C403.2.7.1& Indicate all ductwork constructed and sealed per IMC,C402 leakage YE$ C403.2.7.3 Duct construction re uirements and IBC va or retarder re uirements M 1.0 YES 403.2.7.3.1- Duct pressure Identify location of low,medium and high pressure ductwork on plans classifcations M 1.0 C403.2.7.3.3 High pressure duct leakage Indicate high pressure duct leakage testing requirements on plans;provide N/A test test results to urisdiction when completed YE$ C403.2.7.1/ Duct insulation Indicate R-value of insulation on ductwork M 1.0 Piping Systems YES C403.2.8 Piping insulation Indicate R-value of insulation on piping M1.1 YES C403.2.8.1 P�Ping insulation exposed to Indicate method of protection from damage/degredation M 1.1 weather SIMPLE SYSTEMS Qualifying Systems C403.3 Qualifying single zone Verify unitary or packaged equipment does not exceed capacity limits,does YE$ s stems not have active humidifcation or simultaneous heatin /coolin M1.0 C403.3 Qualifying 2-pipe heating Verif 2- i e heatin onl s stem does not exceed ca acit limits N/A s stems Y P P g y y P Y N/A C403.3.2 Hydronic system controls Refer to Complex Systems Seclion C403.4.3 Simple System Economizers YES C403.3.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equip M 1.0, M 1.1 sched. YES C403.3.1.1.1 Air economizer capacity Indicate modulaling OSA control capability up to 100%OSA,or exception M 1.0, M 1.1 YE$ C403.3.1.1.3 Air economizer high limit Indicate high limit shut-off control me�hod per Table C403.3.1.1.3(2) controls M 1.0 YE$ C403.1.12 Integrated air economizer Indicate capability for partial air economizer operation tor systems with M1.0 o eration ca acit >65 D00 btuh YES C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with M 1.0 f COMPLEX SYSTEMS Complex System Economizers C403.4.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equip N/A sched. C403.4.1.4 Economizer heating system Verify control method of HVAC systems with economizers does not N/A impact increase building heating energy usage during normal operation N/A C403.4.1.3 Integrated economizer Indicate capability for partial economizer operation for air or water econo o eration s stems Moved Water economizer capacity Indicate water econo capable of 100%cooling capacity at 50�F db/45`F wb N�q osn C403.4.L2 Water economizer Indicate precooling coils and heat exchangers do not exceed pressure drop N/A maximum pressure drop limit N/A C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with n i � �/