9600 HOLLY DR CHALLENGER ELEMENTARY SCHOOL 2017-12-20

Module Selection Inform•tion Continued Expansion, System and Remote Power Supplies and Accessories (Continued) Model Description Size Current 4100-5152 12 VDC Power Option,2 A maximum 1 Block 1.5 A maximum 4100-0156 8 VDC Converter, required for multiple Physical Bridge Modules,3 A maximum 1 Block included w/loads 4100-0636 Box Interconnection Harness Kit(non-audio); order one for each close-nippled cabinet 4100-0638 4100 Slot Module Additional 24 VDC Harness; need when 4100 Slot module requirements exceed 2 A from SPS 8 Zone Initiating Device Circuits* Expansion Signal Module and Options(1.5 A Class B except as noted) Model Type I Supv. Alarm Model Description Supv. Alarm ---> 4100-5005 Class B 75 mA 195 mA 4100-5116 Converts 1 NAC in to 3 NACs out; 1 Block size 18 mA 80 mA 4100-5015 Class A 75 mA 195 mA 4100-1266 Expands 3 NACs to 6 select one;mounts 0.6 mA 60 mA *IDC Modules are 1 Slot size 4100-1267 Converts 3 NACs to Class A on 4100-5116 0.6 mA 30 mA Addressable Interface Modules (refer to location reference on pages 8 and 9) Model Description Supv. Alarm no devices 50 mA 60 mA IDNet 2 Module,250 point capacity;electrically isolated output with two short circuit isolating Class B or Class A output loops, 1 block;standard on EPS with 50 devices 90 mA 150 mA 4100-3109" ZDNet 2 Module; alarm currents for 50 and above devices includes 20 device 125 devices 150 mA 225 mA LEDs in alarm 250 devices 250 mA 350 mA ZDNet 2+2 Module,250 point capacity; electrically isolated output with four no devices 50 mA 60 mA short circuit isolating Class B or Class A output loops, 1 block; mounts in 50 devices 90 mA 150 mA 4100-3110* expansion bay or available master controller bay module locations only, not — -- applicable for EPS mounting;alarm currents for 50 and above devices includes 125 devices 150 mA 225 mA 20 device LEDs in alami 250 devices 250 mA 350 mA 4100-3111* IDNet Short Circuit Isolating Loop Output Module;mount up to two on a 4100-3109 module;for use with 4100-3109 modules; this option is for aftermarket field installation only *Note: Loading per ZDNet device(no LEDs on)=0.8 mA supervisory and 1 mA alarm. Each IDNet 2 and IDNet 2+2 Short Circuit Isolating Loop Output can be individually controlled for system diagnostics and can be assigned a public poin:for Fire Alarm Network annunciation. Model Description Supv. Alarm MAPNET II Module, 127 point capacity, add devices Module without devices 255 mA 275 mA 4100-3102 separately; Module size=2 Slots; Loading per MAPNET II device=1.7 mA Fully loaded module,total 471 mA 491 mA Isolator Module for MAF'NET II communications; converts a single connected SLC 4100-3103 into four isolated outputs selectable as Class A or Class B; up to two Isolator Modules 50 mA 50 mA can be connected to one SLC; Module size= 1 Slot; NOTE:Compatible with MAPNET II Remote Isolators only Relay Modules; Nonpower-limited (for mounting in expansion bay only, refer to location reference on pages 8 and 9) Model Description Resistive Ratings Inductive Ratings Size Supv. Alarm 4100-3202 4 DPDT w/feedback 10 A 250 VAC 10 A 250 VAC 2 Slots 15 mA 175 mA 4100-3204 4 DPDT w/feedback 2 A 30 VDCNAC 1/2 A 30 VDC/120 VAC 1 Block 15 mA 60 mA 4100-3206 8 SPDT 3 A 30 VDC/120 VAC 1-1/2 A 30 VDC/120 VAC 1 Block 15 mA 190 mA Current Calculation Notes: 1. To determine total supervisory current, add currents of modules in panel to base system value and all external loads powered by panel power supplies. 2. To determine total alarm current,add currents of modules in panel to base system alarm current and add all panel NAC loads and all external loads powered from panel power supplies. Continued on next page S4100-0031-30 12/2014 %I� .'