607 SE EVERETT MALL WAY NORTH CORNER STUDIOS 2019-01-28

Lighting, Motor, and Electrical Permit Checklist, Pg. 1 LTG-CHK 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2,R3,R4 over 3 stories and all R1 Revised August 2016 Project Title: NORTHCORNER STUDIOS(FITNESS CENTER) (Date 8.29.17 The following information is necessary to check a permit application for compliance with the lighting,motor,and electrical requirements in the Washington State Energy Code,Commercial Provisions. Applicability Location In Budding Department (yes,no,na) Code Section Component Compliance information required in permit documents Documents Notes LIGHTING CONTROLS C405.2 Lighting controls, For all lighting fixtures,indicate lighting control method on plans for general spaces and lighting zone(s)served,or exception taken Luminaire level Indicate on plans all fixtures provided with LLLC in lieu of C405.2 C405.2 lighting controls lighting controls;provide description of control capabilities and (LLLC) performance parameters Lighting in dwelling For permanently installed lighting fixtures in dwelling units,indicate C405.1 lighting control method on plans for spaces and lighting zone(s) units served,or demonstrate compliance with high efficacy exception C405.2.3 Indicate on plans the method of manual lighting control(whether C405.2.1.1 combined with occupancy sensor,automatic light reduction, C405.2.2.2 Manual controls daylight responsive or specific application controls),location of C405.2.4 manual control device and area or specifice application it serves C405.2.5 C405.2.2.1 Manual interior lighting Indicate on plans which method of manual 50%lighting load C405.2.2.2 reduction is provided,or whether lighting load is reduced via C405.2.3 controls occupancy sensors or daylight responsive controls Indicate on plans the method of automatic shut-off control during unoccupied periods(occupancy sensor or time switch)for all C405.2.2 Method of automatic lighting zones; shut-off control Indicate locations where automatic shutoff is provided by other methods(occupancy sensor or digital timer switch)or which time switch control exception applies Indicate on plans the spaces served by occupancy sensors; C405.2.1 Occupancy sensor Indicate whether occupancy sensor controls are configured to be C405.2.1.1 controls manual-on,automatic 50%-on,or serve a space eligible for automatic 100%-on per exception C405.2.1.2 Occupancy sensor Indicate aisleways and open areas in warehouse spaces provided controls-warehouses with occupancy sensor controls that reduce lighting power by 50% C405.2.6 Digital timer switch Indicate required digital timer switch control function when control is used C405.2.2.1 Automatic time switch Indicate locations of override switches on plans and the lighting controls zone(s)served,include area sq.ft. Indicate primary and secondary sidelight daylight zone areas on plans,include sq.ft.; C405.2.4.2 Daylight zones- Indicate toplight daylight zone areas on plans,include sq.ft.; C405.2.4.3 Sidelight and toplight For small vertical fenestration assemblies(rough opening less than 10 percent of primary daylight zone)where daylight responsive controls are not required,provide fenestration area to daylight zone calculation(s) Indicate on plans lighting zone(s)served by daylight responsive controls; Identify sidelight and toplight daylight zones that are not provided Daylight responsive with daylight sensing controls and the exception(s)that apply; C405.2.4 controls Indicate on plans the lighting load reduction method-continuous dimming,or stepped dimming that provides at least two even steps between 0%-100%of rated power; Indicate that daylight sensing controls are configured to completely shut off all controlled lights in the lighting zone Additional controls Identify spaces and lighting fixtures on plans that require specific C405.2.5 Specific application lighting controls application lighting controls per this section Indicate on plans that display and accent lighting,and display case C405.2.5- Display and accent lighting are controlled independently from both general area Items 1&2 lighting lighting and other lighting applications within the same space; Indicate manual and automatic lighting control method (1-...._..167.../1/12